TAYO Zontes ZT125-M 2022, Руководство по обслуживанию

Страница: 165 / 188

165 / 188
3. Reinstall the shock absorber, front fender, front
wheel and other components
a.Pry a gap on the lower connecting plate with a flat-
headed batch, insert the corresponding shock absorber,
install the shock-absorbing in place, take the next batch,
screw in two M10×1.5×43 bolts
⑸
, use a 14# sleeve Tighten
two M10×1.5×43 bolts
⑸
, torque: 55N.m (5.6 kgf.m, 41 lbf.ft)
b. Use the same method to install another shock absorber.
c. Pick up the front wheel and install the bushing, align the
mounting holes between the two shock absorbers, penetrate
the front wheel axle, and tighten the front wheel axle with a
17# inner hexagon. Torque: 50N.m (5.1 kgf.m, 37 lbf.ft). If
one of the shock absorbers is not installed in place, the front
axle will not be tightened or can not be inserted into the right
shock absorber. You need to remove the shock absorber that
is not in place and install it in place.
d. After installing the front wheel, use the 6# inner
hexagon to tighten the two M8×35 bolts at the bottom of the
right front shock absorber, torque: 20N.m (2.0 kgf.m, 15
lbf.ft).
e. First use a single batch to separate the two brake pads
inside the brake caliper. If the resistance is too large and the
two brake pads cannot be separated, please refer to the
method of "Adding Brake Fluid" to remove the upper cover of
the disc brake oil cup and then separate it. 2 brake pads,
align the gap between the 2 brake pads in the disc brake
caliper with the brake disc on the front wheel and install it.
Then use a 14# sleeve to tighten two M8×37 bolts (2),
torque: 24N.m (2.5 kgf.m, 18 lbf.ft).
f. Press the position held when the front mud plate is
removed, pass through the appropriate position in the
middle of the shock absorber, and install it to the
corresponding position, use the 4# inner hexagon to reinstall
the 2 M6×12 bolts (3), do not miss the installation of the
lining Set
⑷ , and cushion rubber ⑸ . Then use the 5# inner
hexagon to reinstall the two M6×30 bolts
⑴
,
Caution:
the left
M6×30 bolt ⑴ needs to have a spring washer ⑹ .
●The vehicle must be parked on a level and stable ground or
on a lifting platform.
●After the front wheel is installed, please press the brake
handle repeatedly until the brake restores the braking effect.
Replace the lower link board
Caution:
●After the front wheel is disassembled, please do not press
the brake handle.
●When the disc brake oil cup is removed, it must be vertically
upward to prevent air from entering the brake pipeline.
●After disassembly, make sure that all parts are installed
correctly.
●Appropriate amount of grease should be applied when
installing the bearing.
●The M 125 steps are similar to the M310, taking the M310 as
an example.
1. Disassemble parts ahead of time
Refer to "Replace the front wheel", "Replace the front
shock absorber", "Replace the steering handle", and remove
the front wheel, front shock absorber, and direction handle.
2. Remove the faucet lock
a. Turn on the vehicle, press the 2 front storage box
switches at ① to open the left and right storage boxes.
b. Use 4# inner hexagon to remove 4 M6×14 bolts , and 2
M6×16 bolts; then use 4# inner hexagon or other tools to
remove The two swell nails on the lower storage box, take
out the left and right storage boxes, the left storage box has a
line connection, do not pull it vigorously, just place the foot
pedal.
c. Extend the 10# torx wrench from the gap in the storage
box, remove the two M6×20 bolts on the faucet lock support,
remove the faucet lock and faucet lock support, no need to
connect the faucet lock and the faucet Remove the lock and
put it in a suitable place next to it.