background image

3-2  

SAFETY

Model 490 

Safety 

If the supply cord is damaged, it must be 

replaced by an authorized Taylor service 

technician in order to avoid a hazard.

Secure the supply cord ground lead to the 

machine in a location where if the cord is pulled, 

the main power leads will become taut before 

the ground lead can break loose.

Failure to follow these instructions may result in 

electrocution. Contact your local authorized Taylor 

distributor for service.

WARNING! 

Avoid injury.

DO NOT

 allow untrained personnel to operate 

this machine.

DO NOT 

operate the machine unless all service 

panels and access doors are restrained with 

screws.

DO NOT 

remove any internal operating parts 

(including, but not limited to, the freezer door, 

beater, or scraper blades), unless all control 

switches are in the OFF position.

Failure to follow these instructions may result in severe 

personal injury, especially to fingers or hands, from 

hazardous moving parts.

WARNING!

 This machine has many sharp 

edges that can cause severe injuries.

DO NOT

 put objects or fingers in the door 

spout. This may contaminate the product and 

cause severe personal injury from blade 

contact.

USE EXTREME CAUTION 

when removing the 

beater assembly. The scraper blades are very 

sharp.

IMPORTANT! Access to the service area of 

the machine must be restricted to persons having 

knowledge and practical experience with the machine, in 

particular as far as safety and hygiene are concerned.

CAUTION! 

This machine must be placed on a 

level surface. Extreme care should be taken when 

moving the machine for any reason. Two or more 

persons are required to safely move this machine. 

Failure to comply may result in personal injury or damage 

to the machine.

NOTICE!

 Cleaning and sanitizing schedules 

are governed by your federal, state, or local regulatory 

agencies and must be followed accordingly. Please refer 

to the cleaning section of this manual for the proper 

procedure to clean this machine.

CAUTION! 

This machine is equipped with a 

refrigerated cabinet, designed to maintain product 

temperature at or below 40°F (4.4°C). Before 

replenishing the mix supply, the product must be 

refrigerated at or below 40°F (4.4°C). Failure to follow 

this instruction may result in health hazards and poor 

freezer performance.

DO NOT

 run the machine without product. Failure to 

follow this instruction can result in damage to the 

machine.

DO NOT

 obstruct air intake and discharge openings. A 

minimum of 3 in. (76 mm) of air clearance on both sides 

of the machine is required. It is recommended to place 

the rear of the machine against the wall to prevent the 

recirculation of warm air. Failure to follow this instruction 

may cause poor freezer performance and damage to the 

machine.

For Indoor Use Only:

 This machine is designed to 

operate indoors, under normal ambient temperatures of 

70°F to 75°F (21°C to 24°C). The machine has 

successfully performed in high ambient temperatures of 

up to 104°F (40°C) at reduced capacities.

Noise Level: 

Airborne noise emission does not exceed 

78 dB(A) when measured at a distance of 39 in. (1.0 m) 

from the surface of the machine and at a height of 62 in. 

(1.6 m) from the floor.

!

!

!

Содержание 490







































Отзывы: