background image

Maintenance, Service, and Repair

              

Batteries 
Page 8

Storage Temperature 

(F)

Charging 

Interval 

(months)

Over 60

1

Between 40 and 60

2

Below 40

6

STORAGE AND RETURNING TO SERVICE

Explosive mixtures of Hydrogen gas are 

present within battery cells at all times. Do 

not work with or charge battery in an area 

where open flames (including gas furnace 

or water heater pilots), sparks, cigarettes, 

or any other sources of combustion are 

present. Always provide ample ventilation 

in rooms where batteries are being charged.  

Failure to do so may result in severe bodily 

injury and/or property damage.

Battery electrolyte will stain and corrode 

most surfaces. Immediately and thoroughly 

clean any surface outside of the battery 

that the battery electrolyte comes in 

contact with. Failure to clean may result in 

property damage.

1. Make sure the key-switch is in the “OFF” 

position, then remove the key.

2. Place the forward-reverse switch in the 

center “OFF” position.

3. Set the park brake. 
4. Place blocks under the front wheels to 

prevent vehicle movement.

5. Disconnect the main positive and 

negative cables at the batteries.

A battery is a live electrical source. It 

cannot be disconnected or neutralized. Do 

not drop any tool or conductive object onto 

the battery. A conductive object that comes 

in contact with the battery terminals will 

initiate a short circuit of the battery. This 

could cause the battery to explode resulting 

in  severe  bodily  injury  and/or  property 

damage.

Battery electrolyte is poisonous and 

dangerous. It contains sulfuric acid. Avoid 

contact with skin eyes or clothing. Wear 

rubber gloves and safety glasses while 

servicing batteries. DO NOT INGEST!  This 

may result in severe bodily injury. 

Storage

Thoroughly clean the batteries and battery compartment. 
Refer to 

Cleaning 

in this section for information 

regarding cleaning the batteries.

Check the electrolyte level and charge the batteries. 
Refer to 

Watering 

in this section for information 

regarding checking the electrolyte level.

Store the vehicle or batteries in a cool, dry, well ventilated 
area.

If storing for more than one month, the batteries should 
be charged as follows:

If the batteries are removed from the 

vehicle, do not place them directly on the 

ground, concrete or solid metal surface. It 

is recommended to store them on a wooden 

pallet or equivalent. Storing on the ground, 

concrete or solid metal surface will cause 

the batteries to discharge and may result 

in premature failure of the batteries.

Содержание SC 0-90



































































































































Отзывы: