background image

Front Axle

Page  30

Bigfoot G-1500

MB-440-10

REPLACE STEERING KNUCKLE

This section is one section of a complete service 

manual. Before starting any procedure, read all 

warnings and instructions that are located in the 

Service Guidelines chapter.

WARNING

Do not allow the brake body or caliper to hang by the 

brake hose. Hanging by the brake hose may damage 

the brake hose resulting in loss of brakes which may 

cause serious bodily injury and/or property damage.

WARNING

Install

1:  Thoroughly clean the kingpin, 

thrust bearing, knuckle, wheel 

bearings, and hub.

2:  Inspect the thrust bearing 

bronze washer. Replace if any 

grooves worn flat.

3:  Pack the thrust bearing with grease.

4:  Lightly coat the kingpin bushings with grease.

5:  Place the thrust bearing on top of the steering 

knuckle with the inner race facing down.

6:  Insert the knuckle bearing assembly into the 

axle and insert the kingpin up from the bottom 

mounting flange.

7:  Install the steering stop bolt.

8:  Tighten the kingpin nut so that there is no vertical 

play in the knuckle but it still turns freely.

9:  Install the ball joint and tighten nut to torque 

specified at the end of this section.

10: Pack wheel bearings with grease.

11:  Install the rear bearing and new grease seal.

12: Install the hub onto the spindle and adjust the 

bearing preload  per procedure in the section.

13: Install a new cotter pin and bearing cap.

14: Grease the bushings.

15: Install the wheel, remove the blocks from behind 

the wheels and test drive the vehicle.

Remove

1:  Raise the front of the vehicle and support with 

jack stands.

2:  Remove the tire/wheel assembly. Refer to Tires 

and Wheels section for information regarding 

removing the tire/wheel assembly.

3:  Remove the hub bearing cap, cotter pin and nut, 

then remove the hub from the steering knuckle.

Note:  If equipped with front brake option you must 

remove the brake body before removing 

the hub. Refer to the Brakes section for 

information regarding the removal of the 

brake body. Do not remove the hydraulic 

brake line from the brake body. If the brake 

line is removed then it will be necessary to 

bleed the brakes.

4:  Remove the ball joint from the steering arm.

5:  Remove the steering stop bolt.

6:  Remove the king pin nut.

7:  Using a large brass drift punch, drive the king pin 

out of the axle and remove the steering knuckle 

and thrust bearing.

Содержание Bigfoot G-1500























































































































Отзывы: