Taylor-Dunn B0-210-36 Скачать руководство пользователя страница 34

Страница: 34 / 188

Front Axle

Page 34

B-200 & B-210 Models

MB-210-13

REPLACE FRONT WHEEL
BEARINGS

1: Set the park brake.

2: Disconnect the batteries.

3: Raise the front of the vehicle and support with

jack stands.

4: Remove the tire/wheel assembly from the hub.

Refer to the Tire/Wheel section for information

regarding removing the tire/wheel assembly.

5: Remove the hub dust cap, cotter pin, and spindle

nut.

6: Remove the hub from the steering knuckle.

Note: For a front disc brake option you must

remove the brake body before removing

the hub. Refer to the Brakes section for

information regarding the removal of the

brake body.

7: Thoroughly clean all grease from the inside of the

hub and the bearings.

8: Inspect and replace the races and bearings as a

set.

Note: It is recommended to replace all four

bearings and races in the left and right

wheels as a set.

9: Assemble in reverse order, using new grease

seals.

a. Pack inner and outer bearings with grease.

b. Adjust the bearing preload per specifications in

the Adjust Front Wheel Bearing procedure.

d. Install a new cotter pin.

10: Install the hub dust cap.

11: Reinstall the brake body. Refer to the Brakes

section for information regarding the installation

of the brake body.

12: Reinstall the tire/wheel. Refer to the Tire/Wheel

section for information regarding installing the

tire/wheel assembly

13: Lower the vehicle.

14: Reconnect the batteries.

15: Remove the blocks from behind the wheels.

16: Release the park brake and test drive.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

REPLACE STEERING KNUCKLE

1: Raise the front of the vehicle and support with

jack stands.

2: Remove the tire/wheel assembly. Refer to Tires

and Wheels section for information regarding

removing the tire/wheel assembly.

3: Remove the hub bearing cap, cotter pin and nut,

then remove the hub from the steering knuckle.

Note: For a front disc brake option you must

remove the brake body before removing

the hub. Refer to the Brakes section for

information regarding the removal of the

brake body. Do not remove the hydraulic

brake line from the brake body. If the brake

line is removed then it will be necessary to

bleed the brakes.

4: Remove the drag link and/or tie rod from the

steering knuckle. Refer to Replace the Ball Joints,

Tie Rods, Drag Link in this section for information

regarding removal of the drag link or tie rod.

5: While supporting the knuckle, remove the king

pin and thrust bearing.

6: Remove the knuckle from the axle.

7: Thoroughly clean and/or replace all bearings,

nuts, washers, and bushings.

Note: Both the left and right side bushings and

thrust bearings should be replaced as a set.

8: Assemble in reverse order.

a. Pack the thrust bearing with grease.

b. Tighten the king pin nut until all of the up and

down play is removed and the yoke rotates

freely. The rubber washer must compress slightly

to create a seal for the grease.

c. Refer to Replace Front Wheel Bearings for

information regarding proper tightening of the

spindle nut

d. Install new cotter pins.

9: Realign the wheels. Refer to the Steering section

for information regarding realignment of the front

wheels.

10: Lower the vehicle.

11: Reconnect the batteries.

12: Remove the blocks from behind the wheels.

13: Release the park brake and test drive.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

Содержание B0-210-36





























































































































































































Результаты поиска

Содержание B0-210-36

Отзывы:

Похожие инструкции для B0-210-36

Бренды по названию

Популярные бренды

Taylor-Dunn B0-210-36, Инструкция по обслуживанию и замене запасных частей

Результаты поиска

Содержание B0-210-36

Отзывы:

Похожие инструкции для B0-210-36

Бренды по названию

Популярные бренды