Making ESE pods coffee
Follow the steps indicated before according to
one cup powder coffee filling BUT instead of
placing powder coffee, place the ESE pod in
the filter.
Once the filter holder is in its place, press the
1cup button.
The coffee machine will stop automatically once
the coffee is brewed.
Hot Water
From heated position, place a cup under the
steam tube.
Open the steam knob turning it forward. Hot water
will start coming out.
To end, close the water system by turning the
knob in reverse.
Milk frothing
From heated position, press the steam button. It
will start blinking.
Once the button stops blinking, the machine will
be ready to make dry steam.
Place a vase with milk under the steam and
introduce the steam tube until the outlet is
nearly at the bottom of the vase.
Open the steam knob turning it forward. The
noise of the steam coming out will be heard.
Regulate the temperature by the touch with the
vase and when you see it ready, close the
steam knob.
NOTE: Once the steam is done, if we want to
return to the coffee extraction, we must press
the button for one or two coffees and release
pressure following the steps of HOT WATER in
this manual. Releasing a little water will lower
the temperature and release the pressure.
SETTING UP THE COFFEE QUANTITY
In the two electronic functions of this coffee
maker (make one coffee or two coffees) you
can set up their duration.
To do this, prepare the machine according to the
function you wish to set up (make 1 coffee,
make 2 coffees).
Press the button of the function you wish to sety
up for 3 seconds.
You will see that the other buttons stop
illuminating.
Press the button again to start the setting.
Remember to place a cup under the filter
holder.
When you reach the desired duration, press again
to record the amount.
NOTE: The “1 coffee” function can be
programmed between 25 and 60 ml. The “2
coffees” function can be programmed between
70 and 110 ml.
STAND-BY FUNCTION:
In order to save energy, the appliance passes to
stand-by after 29 minutes/seconds if the user
does not use it.
When the appliance enters to StandBy function,
the on/off button will keep blinking slowly.
ONCE YOU HAVE FINISHED USING THE
APPLIANCE:
Turn the appliance off, using the on/off switch.
Unplug the appliance from the mains.
Let the appliance to cool down.
Clean the appliance.
CLEANING
Disconnect the appliance from the mains and
allow it to cool before undertaking any
cleaning task.
Clean the equipment with a damp cloth with a few
drops of washing-up liquid and then dry.
Do not use solvents, or products with an acid or
base pH such as bleach, or abrasive products,
for cleaning the appliance.
Do not let water or any other liquid get into the air
vents to avoid damage to the inner parts of the
appliance.
Neither parts of this appliance are suitable for
cleaning in the dishwasher.
The draining/drying position of the articles
washable in the dishwasher or in the sink must
allow the water to drain away easily (Fig.?).
Then dry all parts before its assembly and
storage.
HOW TO DEAL WITH LIME SCALE
INCRUSTATIONS:
For the appliance to work correctly it should
be kept free of limescale or magnesium
incrustations caused by the use of hard water.
To prevent this kind of problem, we recommend
the use of water with low lime or magnesium
mineralisation.
This coffee maker is prepared to remind you to
descale the machine after 500 cycles. This
time is a guideline and we recommend the
following:
Every 10 weeks if the water is “very hard”.
Every 17 weeks if the water is “hard”.
Homemade solutions are not recommended in
the decaling of this appliance, such as the use
of vinegar.
Euforia_en.indd 7
Euforia_en.indd 7
14/07/2022 15:51:14
14/07/2022 15:51:14
Downloaded by: pd-oliana on 06-09-2022 15:21 CEST