AFTER SALES SUPPORT
1300 922 271
MODEL NUMBER: BT-RH1500, 08/11
6
c.
Hold the equipment by the insulated handles
when carrying out work during which the plug-in
tool could strike concealed power cables or its
own mains lead.
Contact with a live cable can also
make the metal parts of the equipment live and
will cause an electric shock.
Additional Safety Rules
•
Check that your mains voltage is the same as
that marked on the rating plate.
•
If you use a cable reel, run all the cable off the
reel. The minimum conductor cross section
used should be 1.5 mm
2
.
•
If you use this electric hammer drill outdoors
you must connect it using a suitable H07RN-F
3G 1.5mm
2
extension cable with a spray-water
protected plug.
•
Make sure of your footing, particularly when
working free-handed on ladders or scaffolding.
•
Use a detector to localize pipes and/or cables
in walls with concealed electric, water or gas
lines.
•
Avoid any contact with conducting electrical
parts or lines.
•
Wear ear-muffs to protect your hearing: Risk
of progressive loss of hearing!
•
Wear goggles and use a breathing mask on
dusty jobs.
•
Never use the machine near vapors or
combustible liquids.
•
Always unplug the machine before cleaning it
or changing drill bits etc.
•
Keep the power cable safe from damage. Oil
and acids can damage cables.
•
Never overload the machine.
•
Important! Follow all safety regulations in your
country applicable to the installation, use and
maintenance of the machine.
•
Chisel bits and drill bits can be inadvertently
thrown out from the machine and cause
serious injury.
•
Always check that the chisel bit or drill bit is
firmly locked in the chuck before you start
work.
•
Check the chuck for wear or damage at regular
intervals.
•
Do not start a hammering tool until it is
pressed against a workpiece (wall, ceiling,
etc.).
•
Always unplug the hammer drill when you
have finished working and remove the chisel
bit or drill bit from the tool.
•
Always unplug the machine before changing
chisel bits or drill bits etc.
•
Protect eyes and assistants from small flying
parts and splinters. Wear a helmet! Erect a
screen wall!
•
Use workgloves to protect fingers from
crushing and skin from grazing.
•
Vibrations can be harmful to the hand-arm
system: Keep the impact time of vibrations
to
a minimum.
•
Always keep the power cable away from where
you want to drill.
•
Keep the machine out of children’s reach.
•
Always hold the machine with two hands when
it is running and make sure of your footing.
•
Make sure that the switch on the machine is set
to the correct position for the work you want
to perform before you put the machine into
operation.
•
If the switch is not in the correct position you
risk suffering bodily injury when the machine
starts to run.
Do not lose these safety instructions
“Caution - Read the operating
instructions to reduce the risk of inquiry”
Wear ear-muffs.
The impact of noise can cause damage
to hearing.
Wear a breathing mask.
Dust which is injurious to health can be
generated when working on wood and
other materials.
Never use the device to work on any
materials containing asbestos!
Wear safety goggles.
Sparks generated during working or
splinters, chips and dust emitted by the
device can cause loss of sight.
Important!
When using equipment, a few safety precautions
must be observed to avoid injuries and damage.
Please read the complete operating manual with due
care. Keep this manual in a safe place, so that the
information is available at all times. If you give the
equipment to any other person, give them these
operating instructions as well.
We accept no liability for damage or accidents which
arise due to non-observance of these instructions
and the safety information.
Recommendation
We recommend that the tool always be supplied via
residual current device with a rated residual current
of 30 mA or less.
