Taurus ALPATEC MSB 2000, Руководство пользователя

Страница: 15 / 88

D Timer button
E Open window detector
F OK button
G Heater setting
ASSEMBLING THE WALL BRACKET:
- The appliance has a wall support (Fig.1) to
support the product.
-Fix the wall support as you think appropriate,
using wall plugs, screws, adhesive...
-Taking into account the separation distances
mentioned above, place the wall support in the
required position and mark the drilling points on
the wall (Fig.2).
-Drill on the marks and introduce the plugs
(Fig.3).
-Fit the support, lining up its holes with those of
the plugs, and screw on (Fig.4).
-Make sure that the bracket is firmly fixed; it
should be able to support twice the weight of the
appliance.
-Fit the appliance into the wall support.
-Now follow the instructions in Figures 5,6,7.
INSTRUCTIONS FOR USE
BEFORE USE:
-Make sure that all the product’s packaging has
been removed.
-Some parts of the appliance have been lightly
greased, consequently, the appliance may give
off a light smoke the first time it is used. After a
short time, this smoke will disappear.
-To eliminate the smell given off by the appliance
when used for the first time, it is recommended
to have it on at full power for 2 hours in a well-
ventilated room.
-Prepare the appliance according to the function
you wish to use.
USE:
-Connect the appliance to the mains.
-Turn the appliance on using the on/off switch(a)
-Turn the appliance on using the on/off button.
(B)
HEATER FUNCTION
-Select the heater function by pressing (G) and
select the desired setting: 1800W ( ), 900W
( ) or fan function.
-Check that the thermostat control is set to the
desired temperature.
TEMPERATURE SELECTION
-Select the desired temperature (5-40ºC) by
pressing (A).
-Press (C) to set the desired temperature and
then press (F) to confirm.
SET DAY & TIME:
-When setting the day and time, the unit has to
be in standby mode.
-Press (A) and the icons
1 2 3 4 5 6 7
will light
up, use + or – to set the day, once the required
day is flashing, press (F) to confirm it.
-Press (A) until the hour icon lights up in
order to set the hour, and then OK to confirm it.
-Press (A) until the minute icon lights up
in order to set the minutes, and then OK to
confirm it.
SET PROGRAM:
-When the unit is on standby, press and hold (D)
for 3 seconds , the icon will remain lit until
programming has been completed.
-The icon
1 2 3 4 5 6 7
will light up fully, now use
+ or – to select the desired day of the week,
once selected press OK to confirm. Next, the
1 6 12 18
icon will appear in order to
select when the heater is operating, one mark
per hour, use + or – to select the desired hours
and press OK (F) to confirm.
-To program more than one hour, use + or – for
the ON time, press SET (A) and OK (F) to
confirm, and then press OK (F) to program the
OFF time.
-Once finished, the temperature can be set, 20°
by default, use + or – to specify the desired
temperature (5-40) and OK (F) to confirm.
-In this way the whole week, 7 days, can be
programmed.
-When the weekly programming is operational,
the icon will be lit, to switch this off, or on
again, press (D) and the icon will disappear or
reappear.
NOTE: The program is saved even after turning
off. If the appliance is turned of for five days, all
settings must be made again.
TOWEL WARMING FUNCTION
-Press (E) to switch on the towel warming
function. To cancel this function, press the same
button again.
-During operation, the icon will light up.
-The towel warmer is 200W.