27
I25
I24
I23
I22
I21
I20
I19
I18
tr
th
sl
se
tr
sv
pt
pl
no
nl
it
fr
fi
es
en
de
cz
If no bar display lights up in the battery indicator:
• after 10 min. the tool aggregate and the squeegee will be lifted off the
ground.
• the suction unit then turns itself off after a further 10 sec.
• you then have 10 min. left to get the machine to the battery charger before
the machine turns itself off.
Recycling filter (optional)
Cleaning method
Direct method:
Scrubbing and vacuuming in one pass.
Indirect working method:
Apply the cleaning solution first (only scrubbing), afterwards scrubbing and
vacuuming.
The cleaning methods are described in detail in the ”Method Card”. You can
obtain this from your TASKI partner.
Refilling the solution tank
Solution tank empty indicator:
Drain recovery tank
Recovery tank full indicator
End of operation
Drain the recovery tank / solution tank
The disposal of the soiled water or the cleaning solution must be carried out in
accordance with the appropriate national regulations.
Proceed as follows for both tanks:
• By gently pressing the drive pedal, the machine
is set into motion.
The tools start to turn and the solution is fed
through the centre.
• Press the Slow run button if you are working in
narrow or difficult environments.
The indicator lights up and the drive speed is
reduced.
If none of the bars in the battery indicator have lit
up, drive the machine to the battery charging
unit.
Caution:
The recycling system is not to be used in areas with high hygienic
demand e.g. hospitals, food-processing companies, kitchens, etc.
The recycling system is recommended for low to medium
congested areas only.
• Pull out the key and apply the parking brake (refer to page 25).
• Push the driver seat forward so that it rests on the steering wheel, and open
the tank hood.
• Pull the recycling filter out of the solution tank (Flextank).
• Place the recycling filter into the recovery tank.
Caution:
Maximum permissible water temperature 60°C/140°F.
Under certain circumstances, the driving of the machine can be
impaired by a special combination of surface/soiling and cleaning
product.
This effect can be reduced by special wheel options.
Caution:
Do not clean without solution, as it could cause floor damage.
• When the cleaning solution tank empty indicator
lights up, it is also accompanied by a tone.
Solution tank is empty.
• Pull out the key and apply the parking brake (refer to page 25).
• Refill the machine, see page 26.
• Once the tank is filled, the solution tank empty
indicator continues to stay lit.
• Drive the machine to a desired destination.
• Press the suction unit button.
The display lights up.
• Press the solution button.
The display lights up.
• Press the brush unit button.
The display lights up.
• Slowly press the drive pedal (approx. 5 sec.).
The solution tank empy indicator will thereby be
reset.
• When the recovery tank full indicator lights up,
the squeegee will rise and the suction unit turns
off.
• Drain the recovery tank, see below.
• Stop the flow of solution.
• Drive a few metres further to avoid subsequent dripping.
Very important when using contact pads!
• Press the brush unit button.
The tools will be stopped.
The tool holder rises up.
• Drive on a few metres further in order to pick up the remaining dirty water.
• Now switch off the suction unit.
The squeegee rises and the suction unit keeps
on running for approximately 10 seconds.
• Drive to the drainage location.
Always drain and clean the recovery tank every time you use the
machine.
If the soiled water is allowed to stand, unpleasant smells and the
deposition of the dirt will take place after a few hours.
Caution:
Follow the national regulations and the information provided by
the detergent manufacturer regarding the protection of persons
when draining the tank.
• Pull out the key and apply the parking brake (refer to page 25).
• Remove the drain hose from its holder.
Hold the hose pointing upwards with the opening at the height of
the edge of the tank. Open the red lid and slowly lower the end of
the hose to the drain.
• Lift the solution tank (Flextank) and lay it into the recovery tank.
Cleaning solution is drained into recovery tank to then be removed.
• Remove the empty solution tank (Flextank) from the recovery tank.
