manualshive.com logo in svg

Task Force Tips YE-RF-900, Инструкции по установке, безопасной эксплуатации и обслуживанию

Поделиться
Скачать
Task Force Tips YE-RF-900 Скачать руководство пользователя страница 41

©Copyright Task Force Tips, Inc. 2008-2014 

LIY-500 May 12, 2014 Rev10

41

4.13.3 ELECTRICAL ENCLOSURE WITH AT PARK RELAY

The electronics enclosure provides feedback for the user that the monitor is in the AT PARK position. This electronics enclosure 
contains a circuit board that is equipped with a relay that is energized when the monitor is in use and de-energized when the monitor 
reaches its fi nal PARK location. The contact rating of the relay is 1 amp @ 30VDC for resistive loads and 0.2 amps @ 30VDC for 
inductive loads.

4.13.3.1 ELECTRIC CONNECTIONS

The AT PARK relay has one Form-C contact (common, normally open, normally closed) that can be used.  The fi gure below shows 
the terminal blocks available for user wiring.

AT PARK RELAY

USER TERMINALS

INHIBIT INPUT

Figure 4.13.3.1

Relay / Terminal Location

4.13.4 ELECTRICAL ENCLOSURE WITH INHIBIT INPUT

The electronics enclosure circuit board provides an input to INHIBIT any RC monitor movement.  When active, this input will disable 
all movement commands to RC monitor.  See fi gure 4.13.3.1 for input location. Requires a constant 12 vdc input signal in order to 
be active.

4.14 MULTIPLEX INTERFACE 
CONTROL (YE-CAN#)

This Multiplex Interface Control converts CANbus or multiplex communications into serial communications for controlling a TFT RC 
monitor or valve.  This module is designed to work on a J1939 CANbus system and allows control of all TFT RC Monitors and RC 
Valve Under Monitor. 

Module Installation and Wiring

CANHI

CANLO

Figure 4.14

YE-CAN# module needs to be mounted onto circuit board located 
in electronics interface box.

1) Turn off power and remove lid from electronics interface box.

2) Position module and carefully plug into circuit board. Be careful  

  to line up pins.

3) Connect CANbus wiring to module based on fi gure 4.14.

4) Replace lid onto box.  Be sure to verify gasket is in place and that 

  no wires are pinched between lid and box.

5) Tighten lid screws equally in a criss-cross pattern.

Module Confi guration

The YE-CAN# module can be confi gured based on the users 
requirements. Default confi guration will have DIP switch #1 in the 
ON position with all others off (see CANbus structure document).

Up to four (4) YE-CAN# modules can be installed on the same 
CANbus communication system.  If installing multiple YE-CAN# 
modules, DIP switches #5 & #6 need to be set accordingly (see 
CANbus structure document).

Contact TFT for the most up-to-date

CANbus Structure document.

Содержание YE-RF-900

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды