Task Force Tips HURRICANE Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 36

background image

©Copyright Task Force Tips, Inc. 2008-2014

LIX-300 April 29, 2014 Rev18

15

4.2.2 HORIZONTAL ROTATION TRAVEL STOPS

The range of Horizontal (left-right) travel for the Hurricane RC monitor is limited to 450 degrees or 225 degrees from either side of
a nozzle discharge position. Horizontal (left-right) travel stop bolts may be installed in the monitor to limit travel as shown in fi gure
4.2.2A and 4.2.2B. Note that left and right are relative to the “Straight Back Reference Mark” shown in fi gure 4.2.2A, and refer to the
operator’s position behind the monitor, opposite the nozzle’s discharge direction. Also, Figure 4.2.2A shows the range of travel for
the various stop bolt locations along with installation notes as shown in Figure 4.2.2B. Horizontal travel for the Hurricane is shown
in fi gure 4.2.2C.

LOCATION OF

STRAIGHT BACK

REFERENCE MARK

Fig 4.2.2A

Horizontal Travel Limits

90° LEFT

135° LEFT AND RIGHT
(ONLY ONE STOP BOLT
NEEDED FOR THIS
TRAVEL LIMIT)

45° LEFT

STRAIGHT BACK
REFERENCE MARK

90° RIGHT

45° RIGHT

ADJUSTMENT DISK, Y3146
INSTALL ON THIS SIDE OF STOP BOLT TO
REDUCE TRAVEL TO LEFT BY APPROX. 8°
FOR EACH DISK INSTALLED. INSTALL DISKS
ON OTHER SIDE TO REDUCE TRAVEL TO RIGHT.

SET SCREW
#VT37-24SS375

REMOVE SETSCREW AND
INSTALL STOP BOLT TO OBTAIN
DESIRED TRAVEL LIMITS.

Fig 4.2.2B

Horizontal Travel Stop Bolt Locations

Fig 4.2.2C

Hurricane Horizontal Travel

«
...
13
14
15
16
17
...
»

Содержание HURRICANE





































Отзывы:

Нет отзывов

Похожие инструкции для HURRICANE

MicroTouch CT150

Бренд: 3M Страницы: 24

Бренд: Barco Страницы: 47

Бренд: V7 Страницы: 12

Бренд: Deif Страницы: 2

Бренд: TIGEX Страницы: 46

Бренд: Barco Страницы: 74

Бренд: Marshall Electronics Страницы: 2

BABY KANGOORB202

Бренд: Rimax Страницы: 80

Бренд: Yasun Страницы: 19

Бренд: Dynascan Страницы: 31

Бренд: Harris Страницы: 168

Бренд: Tatung Страницы: 47

Бренд: Evelo Страницы: 8

Бренд: Healthy Living Страницы: 33

Бренд: Power Acoustik Страницы: 8

Бренд: Planar Страницы: 20

Бренд: Eaton Страницы: 80

Бренд: Panasonic Страницы: 146

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды