background image

©Copyright Task Force Tips LLC  2011-2019 

LIG-012 March 28, 2019 Rev06

3

1.0  MEANING OF SAFETY SIGNAL WORDS

A safety related message is identifi ed by a safety alert symbol and a signal word to indicate the level of risk involved with a particular 
hazard. Per ANSI standard Z535.6-2011, the defi nitions of the four signal words are as follows:

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious 
injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious 
injury.

CAUTION

CAUTION indicates a potentially hazardous situation which, if not avoided, could result in minor 
or moderate injury.

NOTICE

NOTICE is used to address practices not related to physical injury.

SAFETY INSTRUCTIONS (or equivalent) signs indicate specifi c safety-related instructions of procedures.

2.0 SAFETY

DANGER

An inadequate supply of nozzle pressure and/or fl ow will cause an ineff ective stream and can 
result in injury, death, or loss of property. See fl ow graphs or call +1 219 548-1033 for assistance.

WARNING

The  nozzle  may  be  damaged  if  frozen  while  containing  signifi cant  amounts  of  water.  Such 
damage may be diffi

  cult to detect visually and can lead to possible injury or death. Any time the 

nozzle is subject to possible damage due to freezing, it must be tested by qualifi ed personnel 
before being considered safe for use.

WARNING

This  equipment  is  intended  for  use  by  trained  personnel  for  fi refi ghting.  Their  use  for  other 
purposes may involve hazards not addressed by this manual. Seek appropriate guidance and 
training to reduce risk of injury.

WARNING

Failure to restrain nozzle reaction can cause fi refi ghter injury from loss of footing and/or stream 
protection. Nozzle reaction will vary as supply conditions change: such as opening or closing 
other  nozzles,  hose  line  kinks,  changes  in  pump  settings,  etc.  Changes  in  spray  pattern  or 
fl ushing  will  also  aff ect  nozzle  reaction.  The  nozzle  operator  must  always  be  prepared  in  the 
event of these changes. 

WARNING

If  nozzle  gets  out  of  control  or  away  from  operator,  retreat  from  nozzle  immediately.  Do  not 
attempt to regain control of nozzle while fl owing water. Injury from whipping can occur.

WARNING

Water is a conductor of electricity. Application of water on high voltage equipment can cause 
injury or death by electrocution. The amount of current that may be carried back to the nozzle 
will depend on the following factors:

•  Voltage of the line or equipment
•  Distance from the nozzle to the line or equipment
•  Size of the stream
•  Whether the stream is solid or broken
•  Purity of the water

1

1 The Fire Fighter and Electrical Equipment, The University of Michigan Extension Service, Fourth Printing 1983. Page 47

CAUTION

Fire streams are capable of injury and damage. Do not direct water stream to cause injury or 
damage to persons or property.

Содержание G-Force G A Series





































Отзывы: