Tarts Basic control Скачать руководство пользователя страница 7

© 2014 Tarts Sensors, LLC.  All Rights Reserved.

 

Tarts Basic Control User

’s Guide (12/14)

 

When this property is FALSE, the device will listen for commands continuously, consuming power constantly.  If an 
application is such that it needs Tarts Basic Control to react immediately to things, use this mode. However, you will 
need to power the Basic Control unit with a 3.0 – 3.3 VDC power adapter. 
  

Led Mode: 

The LED (light) indicates if the switch is closed (ON) or open (OFF).  Since the LED will burn power, the user 

has the following mode options.  

ALWAYS_OFF, ALWAYS_ON, FLASH_WITH_POLL

 

  
Poll interval

: the poll interval defines how often the unit checks with the gateway for urgent controls commands (such as 

opening or closing its switch). This interval is typically less than the report interval, but never greater than it. The report 
interval is critical in the amount of delay that is acceptable for the unit reacting to a command to go open or closed, 
when the device is in 

Low Power Mode

. It is ignored when the device is not in Low Power Mode. 

 

Send Control: 

When sending the command, the user can tell the switch to go open, go closed or toggle (switch to the 

opposite state). The user can optionally set a time-duration in seconds for how long this condition should be applied, or 
the user can send a zero (0) for the change to remain indefinitely (until another command is sent or until the device is 
power cycled). 
 
 

Datum Object 

Examples of the data in for Basic Control below

:

 

Sensor Type 

Name 

Value 

FormattedValue 

Basic Control 

SWITCH 

OPEN 

 

Tech specs for this device: 

Radio Bands available: 

900 MHz, 868 MHz, 433 MHz (exclusive on each device) 

Tarts Battery Voltage (HIGH) 

3.6 VDC 

Tarts Battery Voltage (LOW) 

2.0 VDC 

High Power Mode Current: 

25 mA 

Low Power Mode Current (switch closed): 

300 uA 

Low Power Mode Current (switch open): 

0.7 uA 

Switching Time: 

<100 ns 

Switch Voltage: 

Up to 40 VDC 

Switch Current: 

Up to 30 mA 

 

Expected Battery Life (Poll interval set at 60 seconds):

 

Battery Type 

Low Power Mode OFF 

Low Power w/ Switch Primarily Closed  Low Power w/ Switch Primarily Open 

CR2032 

~4 hours 

11 days 

2 months 

AA x 2 

2.5 days 

5 months 

1.5 years 

C x 2 

13 days 

1.5 years 

3+ years 

D x 2 

26 days 

2+ years 

3.5 years 

 

Содержание Basic control











Отзывы: