TapFlo TE Series Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 42

TapFlo TE Series Скачать руководство пользователя страница 14

1. INSTALLATION

IOM manual Tapflo TE series

13

1.8.5.

Air pressure

The pump is equipped with an air treatment system mounted on the side housing of the pump.
The diaphragm is balanced by means of a support plate and

does not require compressed air

to operate

.

When discharge pressure is below 4 bar, pump

can

work without air support to the diaphragm.

Nevertheless over 2 bar on discharge we recommend to use air support for optimal diaphragm
lifetime. Below 2 bar we recommend not to use air support.
The air pressure on the output of the filter-regulator should be set to 1,5

± 0,2 bar. Do not

exceed the recommended air pressure.

Discharge pressure

Air side back-up

0

–

2 bar

Not recommended

2

–

4 bar

Recommended

As prevention purpose, a filtration of the air by means of a 5 micron filter or finer is
recommended. Recommended air quality according to PN-ISO8573-1:2010 is particles class 6,
water class 4 and oil class 4. Dirt or oil in the air can under unfortunate circumstances be the
cause of a breakdown.

ATTENTION!

If air support is utilized, it should only be used during pump operation. When pump has no
counter pressure, the air installation should also be relieved of pressure. Failure to do so may
result in premature diaphragm failure.

1.8.6.

Noise level

At tests, the noise level from a Tapflo pump has not exceeded 80 dB(A). Under some
circumstances, for example if the pump is operating under high speed, the noise can be
inconvenient or hazardous for personnel staying for long periods in the vicinity of the pump.
This hazard can be prevented by:

➢

using suitable ear protection;

➢

lowering the speed of the pump;

➢

using elastomer valve balls (EPDM, NBR or polyurethane) instead of PTFE, ceramic or
stainless steel, provided that the elastomer is compatible with the pumped liquid.

1.8.7.

Temperature hazards

➢

Raised  temperature  can  cause  damage  on  the  pump  and/or  piping  and  may  also  be
hazardous  for  personnel  in  the  vicinity  of  the  pump/piping.  Avoid  quick  temperature
changes  and  do  not  exceed  the  maximum  temperature  specified  when  the  pump  was
ordered. See also general max temperatures based on water in chapter

6

➢

When the pump is exposed to ambient temperature variations or if there is big difference
between the temperature of the product and the surrounding, the tightening torques of
the housing nuts should be checked periodically as part of preventive maintenance (please
contact Tapflo for interval proposals). Ambient temperature limits are form -20

º

C to +40

º

C.

«
...
12
13
14
15
16
...
»

Содержание TE Series











































Отзывы:

Нет отзывов