Tannoy VLS SERIES Скачать руководство пользователя страница 7

5. Wiring and connections

VLS Series Operation Manual  rev 1.0.0

7

    

superior to a lower power amplifier running at 100%. An amplifier with insufficient drive capability will not 
allow the full performance or the loudspeaker to be realised. (See technical specifications section for 
recommended amplifier power.) 

When using amplifiers from different manufacturers in a single installation, make certain that all amplifiers have 
closely matched gains. (Variation should be less than +/- 0.5 dB.) This precaution is important to the overall 
system balance when only a single active crossover is being used with multiple cabinets. When possible, it is 
recommended that the same amplifiers be used throughout.

Series/parallel connections

 - When running low-impedance loudspeakers in parallel, care must be 

taken not to allow the impedance to drop too low, as damage may be sustained by the amplifier. Most low 
impedance amplifiers will be able to handle loads of 2 ohms to 8 ohms. This means for example that when 
using an amplifier with 2 ohm load rating, up to three VLS 30 or six VLS 7/15 may be connected in parallel 
per output, although care should be taken as impedance varies with frequency and at some frequencies the 
impedance will drop to below 2 ohms.

5.3 Constant voltage (70 /100 V) Mode 

In constant voltage distributed systems, normally a number of loudspeakers are connected in parallel to a single 
amplifier output. Connect the positive (+) conductor from the amplifier or prior loudspeaker in the system to a 
positive (+) barrier strip terminal and the negative (-) conductor to a negative (-) terminal. The other parallel 
barrier strip is available for connecting additional loudspeakers.

A multi-position rotary switch on the rear input panel selects either the low-impedance operating mode or the 
high-impedance modes (70 V or 100 V) with available transformer taps. When using VLS Series loudspeakers in 
distributed line systems, the transformer can be tapped with available power levels shown in the table below: 

70 V

100 V

5 W

9.5 W

9.5 W

19 W

19 W

37.5 W

37.5 W

75 W

75 W

150 W

150 W

-

Содержание VLS SERIES

















Отзывы: