19
5.1 Digital 192kHz Set-up
The diagram shows how to connect a 5.1 digital set-up at 192khz.
All Master monitors require installed digital I/O cards.
AES signal is fed to inputs 2&3 of these cards.
}
The Centre monitor is set as the System Controller by leaving
out the TC Link button on the rear panel.
}
The Centre monitor receives audio for both centre & LFE channels
via the AES input connectors (input 2 for Centre & input 3 for Sub).
The LFE subwoofer is fed via the
RJ-45 connection from the left monitor.
}
RJ45 Network connections from the Centre monitor to the Left &
Right monitors are required.
}
The Left Monitor receives audio for both Left & LS channels via the
AES input connector (input 2 for Left & input 3 for LS). The LS
monitor is fed via the RJ-45 connection from the Left monitor.
}
The Right Monitor receives audio for both Right & RS channels via
the AES input connector (input 2 for Left & input 3 for RS). The RS
monitor is fed via the RJ-45 connection from the Left monitor.
}
Clock MUST be sent on the AES connection feeding the Centre/LFE
channels (or on BNC).
}
When no Bass management is selected, only the LFE signal will be
sent to the subwoofer.
}
When Bass management is selected, low frequency content from the 5 main channels
is extracted and sent to the subwoofer where it is summed with the LFE channel
}
The iDP
™
Remote, iDP SOFT
™
or PC-iP
™
can be connected to any spare TC Link “out” connection.
}
! REMEMBER – To set a master monitor as the system controller the TC Link button on the
rear panel MUST be in the out position.
6.1 Analog Set-up
The diagram shows how to connect a 6.1 analog set-up.
}
The Centre monitor is set as the System Controller by leaving out
the TC Link button on the rear panel.
}
The Centre monitor receives audio for both centre (input 1) & LFE
channels (input 2) via the analog input connectors. The LFE
subwoofer is fed via the RJ-45 connection from the left monitor.
}
RJ45 Network connections from the Centre monitor to the Left &
Right monitors are required.
}
The Left Monitor receives audio for both Left (input 1) & LS
channels (input 2) via the analog input connectors. The LS monitor
is fed via the RJ-45 connection from the Left monitor. The CS
monitor is fed via the RJ-45 connector from the LS monitor.
Audio for the CS monitor is fed to analog input connector 1.
}
The Right Monitor receives audio for both Right (input 1) & RS
channels (input 2) via the analog input connectors. The RS monitor
is fed via the RJ-45 connection from the Right monitor.
}
When no Bass management is selected, only the LFE signal will be
sent to the subwoofer.
}
When Bass management is selected, low frequency content from
the 5 main channels is extracted and sent to the subwoofer where it is
summed with the LFE channel. (Only LF, Center, RF, LS, and RS contribute to the bass management signal.)
}
The iDP
™
Remote, iDP SOFT
™
or PC-iP
™
can be connected to any spare TC Link “out” connection.
}
! REMEMBER – To set a master monitor as the system controller the TC Link button on
the rear panel MUST be in the out position.
Содержание Ellipse 8 iDP
