background image

 
 

W W W . T A N N E N - P A R A D I E S . D E

 

 

- 8 - 

Maint storage 

Before carrying out maintenance and repair works, always disconnect the machine from 
the mains. 

 

1) Maintenance after about 50 drilling passages 

Remove the chips from the machine in order not to interfere with the ventilation of 
the motor. Check the grill and the drill chuck for tightness. Always tighten up all 
screws with the Allen keys. 

2) Maintenance after about 10 hours: 

In addition to 1): 

2.1)  if needed, remove  resin  from the drill and sharpen it. 
2.2)  clean the guide bars with a cloth. 

3) Maintenance after about 250 hours:  

In addition to 1) and 2): 
3.1)  Blow  air  vents,  check  the  tightness  of  all  screws.  Check  the  tightness  of 

the gear head. Carbon brushes are designed to work for about 300 hours, 
and can be replaced. 

4) After the season, it would be good practice to clean the unit, lubricate all moving 

parts and keep the drilling machine in a dry place. 

Faults and troubleshooting 

Problem 

Cause 

Removal 

Caution 

Drill stuck firmly  Too  fast  drilling  with  too 

much pressure. 
or: 
Too  slender  tip  of  the 
drill. 
(resharpen) 

Disconnect  the  power,  raise  the  tree  with 
the  pedal,  then  firmly  pull  the  pedal  up. 
Hold the tree vertically above the drill bit. 

 Side 

planning 

or/and  rotation  can 
damage the drilll! 

The 

machine 

does not start 

Power 

Check the cable connection and power. 

While 

checking, 

disconnect  the  unit 
from the mains! 

Drilled  hole  is 
not straight 

Centering  device  is  not 
set properly 

Centering device at a height below the top 
level. 

  

  

Centering 

device 

is 

skewed 

Get  the  centering  slide  all  the  way  down, 
remove  the  horizontal  and  vertical 
irregularities. 

  

Drilled  hole  is 
too deep 

Drill  bit  is  not  embedded 
deeply  enough  in  the 
chuck 

Remove  the  drill  bit.    Clean  of  chips,  net 
and dirt. 

While checking, 
disconnect the unit 
from the mains! 

Drilled  hole  is 
too big 

Plays on the drill or head  Tighten  the  screws  on  the  chuck  and 

tighten the chuck. 

While checking, 
disconnect the unit 
from the mains! 

Drilled  hole  is 
not deep enough 

 drill  shavings  stuck  or 
residual net 

Inspect  the  drill.  Remove  the  chips  and 
residual net, clean the drill. 

While checking, 
disconnect the unit 
from the mains! 

Bad 

drilling 

output 

blunt drill 

Replace  or  sharpen  drill  and/or  clean  the 
drill. 

While checking, 
disconnect the unit 
from the mains! 

The drill remains 
up 

Guide bars dirty 

Clean and dry with a cloth. If the operation 
is not smooth enough lubricate with engine 
oil. 

While checking, 
disconnect the unit 
from the mains! 

Содержание 44640











Отзывы: