manualshive.com logo in svg

Tank Workshop SCHWERE PLATTFORMWAGON SSY 60TON, Руководство пользователя

Поделиться
Скачать
Tank Workshop SCHWERE PLATTFORMWAGON SSY 60TON Скачать руководство пользователя страница 11

Decals & Painting

Use the below figure to locate the decals. Note if you are building the Panther car please 
reference the notes on the figure for the applicable car’s decals.

For painting we recommend you browse the various railroad car colors at your local hobby 
shop or on-line shop. These cars could be painted several colors from a dark grey, black or even 
red. Some may have even been camouflaged. The decking can be stained or painted. You can 
use a wire brush to distress the wood and give it a worn, torn up look. Tank treads were not 
easy on this wood. Look for good references to choose the colors. Even use modern day rail cars 
as reference.

For Panther use this 
decal

TWS 3002 uses 
60ton symbol

White

White

11

345 Wynbrook Dr. McDonough GA 30253                 Copyright 

 

2008       Email: 

[email protected]

Ph:404-516-0477

Содержание SCHWERE PLATTFORMWAGON SSY 60TON












Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды