background image

D14640.01—MARCH 2010 

25

TANDBERG PrecisionHD 1080p/720p camera

Camera User Guide

Contents

Introduction

Physical interface

Cables

Connecti to codec

Video formats

Daisy chaining

Appendices

Contact us

www.tandberg.com

Command

Command 

Packet

Response

Gamma_Mode_Inq

8x 09 04 51 ff

Resp: y0 50 0p ff  
p=2: Auto, p=3: Manual

Gamma_Table_Inq

8x 09 04 52 ff

Resp: y0 50 0p 0q 0r 0s ff  
pqrs: Gamma table in use if manual mode.

Call_LED_Inq

8x 09 01 33 01 ff

Resp: y0 50 0p ff  
p=2: On, p=3: Off, p=4: Blink

Power_LED_Inq

8x 09 01 33 02 ff

Resp: y0 50 0p ff  
p=2: On, p=3: Off

Video_System_Inq

8x 09 06 23 ff

y0 50 0p 0q 0r 0s ff  
pqrs=video mode currently being output on the 
HDMI port. See chapter on DIP switches.

DIP_Switch_Inq 

8x 09 06 24 ff

y0 50 0p 0q 0r 0s ff pqrs contains the bit 
pattern of the DIP switch.  See chapter on DIP 
switches.

IR_Output_Inq

8x 09 06 08 ff

Resp: y0 50 0p ff  
p=2: On, p=3: Off

ALS_RGain_Inq 

8x 09 50 50 ff

Ambient Light Sensor Resp: y0 50 0p 0q 0r 0s 
0t 0u 0v 0w ff 
pqrstuv=32 bit unsigned integer, relative gain 
value. The integration time is a constant set in 
the camera SW.

ALS_BGain_Inq 

8x 09 50 51 ff

ALS_GGain_Inq 

8x 09 50 52 ff

ALS_WGain_Inq 

8x 09 50 53 ff

Up side down_Inq 

8x 09 50 70 ff

Resp: y0 50 0p ff  
p=0: Camera is upright.  
p=1: Camera is upside down.

Command

Command 

Packet

Response

CAM_ID_Inq

8x 09 04 22 ff

Resp: 90 50 zz xx 00 yy ff  
Only zz, which identifies the camera, is relevant. 
zz = 0x50 for this camera.

CAM_SWID_Inq

8x 09 04 23 ff

Resp: y0 50 [1-125 bytes ASCII SWID] ff. Never 
route this message through Sony cameras.

CAM_HWID_Inq

8x 09 04 24 ff

The response is the Module Serial Number 
stored in EEPROM. The number is converted to 
ASCII :  y0 50 [12 bytes ASCII HWID] ff.

Zoom_Pos_Inq

8x 09 04 47 ff

Resp: y0 50 0p 0q 0r 0s ff  
pqrs: zoom position

Focus_Pos_Inq

8x 09 04 48 ff

Resp: y0 50 0p 0q 0r 0s ff  
pqrs: focus position

Focus_Mode_Inq

8x 09 04 38 ff

Resp: y0 50 0p ff  
p=2: Auto, p=3: Manual

PanTilt_Pos_Inq

8x 09 06 12 ff

Resp: y0 50 0p 0q 0r 0s 0t 0u 0v 0w ff  
pqrs: pan position tuvw:  
tilt position

Power_Inq

8x 09 04 00 ff

Resp: y0 50 0p ff  
p=2: On, p=3: Off

WB_Mode_Inq

8x 09 04 35 ff

Resp: y0 50 0p ff  
p=0: Auto , p=6: Table manual

WB_Table_Inq

8x 09 04 75 ff

Resp: y0 50 0p 0q 0r 0s ff  
pqrs: Table used if table mode

AE_Mode_Inq

8x 09 04 39 ff

Resp: y0 50 0p ff  
p=0: Auto, p=3: Manual

Backlight_Mode_
Inq

8x 09 04 33 ff

Resp: y0 50 0p ff  
p=2: On,  p=3: Off

Mirror_Inq

8x 09 04 61 ff

Resp: y0 50 0p ff  
p=2: On, p=3: Off

Flip_Inq

8x 09 04 66 ff

Is video flipped or not?  
Resp: y0 50 0p ff  
p=2: On , p=3: Off

The VISCA™/RS–232 control protocol, cont... 

Inquiries

Содержание PrecisionHD 1080p






























Отзывы: