TANDBERG 770 Скачать руководство пользователя

Страница: 74 / 111

TANDBERG Videoconferencing System

Advanced use

Use CallManager

The codec will use a specific Cisco CallManager identified by the IP-address specified in ‘

CallManager

’. The CallManager replaces a gatekeeper, therefore ‘

Use Gatekeeper

’ must be set to ‘

Off

’ before this

can be done. When ‘

’, ‘

Use Gatekeeper

’ and ‘

Gatekeeper IP

’ is disabled.

Off

The codec will not use Cisco CallManager.

CallManager IP

The CallManager IP-address specified here will be used if ‘

Use CallManager: On

’.

H.323 Prefix

When dialing a number prefixed with digits specified by ‘

H.323 Prefix

’, and with ‘

Net: Auto

’, an H.323 call will be

placed.

Example:

H.323 Prefix is ‘555’. Dialling ‘55582’ with ‘Net:Auto’ will select LAN.

Pressing ‘

’ will send a gatekeeper registration request. This request will also be sent when leaving the

menu.

Содержание 770
















































































































Результаты поиска

Содержание 770

Отзывы:

Похожие инструкции для 770

Бренды по названию

Популярные бренды

TANDBERG 770, Руководство пользователя

Результаты поиска

Содержание 770

Отзывы:

Похожие инструкции для 770

Бренды по названию

Популярные бренды