Tandberg Data SLR AUTOLOADER PROGRAMMER Скачать руководство пользователя страница 61

Страница: 61 / 62

______________________________________________________________________

Tandberg SLR Autoloader SCSI Functional Specifications

3-1

SCSI Status and Messages

3.1

Supported SCSI Status Codes

The following table lists the Status codes supported by the device.

Code

Description

00h

GOOD

02h

CHECK CONDITION

08h

BUSY

18h

RESERVATION CONFLICT

GOOD

This status indicates that the target has successfully completed the
command.

CHECK CONDITION

This status indicates that a contingent allegiance condition has occurred.

BUSY

This status indicates that the target is busy. The recommended recovery
action is to issue the command again at a later time.

RESERVATION CONFLICT

This status shall be returned whenever an initiator attempts to access a
device or element that is reserved to another initiator using the RESERVE
command. The recommended recovery action is to issue the command again
at a later time.

3.2

Supported SCSI Message Codes

The following table lists the Message codes supported by the device.

Code

Description

00h

Command Complete

01h

Extended Message (SDTR & WDTR only)

02h

Save Data Pointer

03h

Restore Pointers

04h

Disconnect

05h

Initiator Detected Error

06h

Abort

07h

Message Reject

08h

No Op

09h

Message Parity Error

0Ch

Bus Device Reset

8Xh-

CXh

Identify

Содержание SLR AUTOLOADER PROGRAMMER































































Результаты поиска

Содержание SLR AUTOLOADER PROGRAMMER

Отзывы:

Похожие инструкции для SLR AUTOLOADER PROGRAMMER

Бренды по названию

Популярные бренды

Tandberg Data SLR AUTOLOADER PROGRAMMER, Руководство пользователя

Результаты поиска

Содержание SLR AUTOLOADER PROGRAMMER

Отзывы:

Похожие инструкции для SLR AUTOLOADER PROGRAMMER

Бренды по названию

Популярные бренды