Tanda TX7210 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 11

Tanda TX7210 Скачать руководство пользователя страница 11

TX7210 Addressable Single Input/Output Module

Installation & Operation Manual

4050100267-Rev1.6-0916

TANDA UK

Specifications are subject to change without prior notice

11

5 Troubleshooting Guide

What you notice

What it means

What to do

Address not enrolling

The wiring is loose
The address is duplicate

Conduct maintenance
Re-Commission the device

Unable to commission

The damage the electronic circuit

Replace the device

Appendix 1

Limitation of Interface Module

The  Interface  Module  cannot  last  forever.  In  order  to  keep  the  interface  module  working  in  good
condition,  please  maintain  the  equipment  continuously  according  to  recommendations  from
manufacturers  and  relative  nation  codes  and  laws.  Take  specific  maintenance  measures  on  the
basis of different environments.

These interface module contains electronic parts. Even though it is made to last for a long period of
time,  any  of these  parts could  fail  at  any time.  Therefore,  test  your module  at  least  every half-year
according  to  national  codes  or  laws.  Any  interface  module,  fire  alarm  devices  or  any  other
components of the system must be repaired and/or replaced immediately as they fail.

«
...
9
10
11

Содержание TX7210












Отзывы:

Нет отзывов