background image

tams elektronik

English

LC modules

LC-8 "Advertising light 4":  

Fusion of the advertising lights 1 to 3,

coming on one after the other. If the input JP2 is switched to earth, the
light sequence switches off after the completion of the active part of
the program. If the input JP2 is switched to earth, the light sequence is
interrupted.   If   the  input  remains   opens,   the   program   is   repeated
constantly.

LC-9 "Ignition module for gas lamps":  

If the input JP2 is given a

short electric  pulse (earth), the gas lamps start to flicker  and  grow
brighter   gradually.   Every   ignition   process   is   slightly   different.   After
approx.   5   seconds   the   gas   lamps   reach   their   maximum   brightness.
During  operation,  the  lamps  flicker  now  and  then  at  different  times
(variations of gas pressure). After the switch-off impulse,  (when the
input   JP2  is   given   a   short   electric   pulse)   all   lamps   shine   on   with
moderate brightness and go off completely in approx. 1.5 seconds.

LC-10 "Fluorescent tube simulator:

 If the input JP2 is given a short

electric pulse (earth), the different fluorescent tubes flicker for a moment
before all of them light one after the other - just like the real thing. The
turning on pattern is a little different for each. If the input JP2 is switched
to earth shortly, the  light   switches off.  When the input is switched to
earth permanently, a defective tube is simulated on output 1. This tube
flickers at irregular intervals, at times brightening quickly, at times slowly.

LC-11 "Occupied   house":  

Two   different   programs   are   available.

Program   1,   "Home",   starts   if   the   input   JP2   is  switched   to   earth,
Program 2, "Office",  if the input remains opens. The programs take
approximately 15 minutes and are repeated after a short pause.
Program 1: First the light in the kitchen (output 1) goes on for a while,
followed a bit later by the living room (output 2). Output 3 is assigned for
connecting a blue light bulb (the TV set), which flickers like a television
picture. Some time later the light in the kitchen switches off, and goes on
again once during the program flow. The light in the bathroom (output 4)

Page 12

Содержание LC Series









































Отзывы: