6300 Series Maintenance Manual
38
Offline Data In
The printer is in Offline condition and unprinted data is in the
buffer. There is no corrective action required. Under normal
conditions, the printer continues to print when it is placed
back Online. If you do not want the buffered data to print,
enter the Clear menu by depressing the Clear key before going
back Online and select the Clear Buffers entry to clear the
buffered data.
Offline Dump On
The printer is in Offline condition and Dump Mode is
enabled. No corrective action is necessary. Place the printer
back Online when you are ready to print.
Online Download
The printer is receiving downloaded fonts or VFU
information. This message will clear when the download is
complete.
Online Dump On
The printer is ready to accept and print data from the host
through Dump Mode. All data received from the host will be
printed in hexadecimal format.
OverflowVFU
An excessive number of bytes has been sent by the host in a
VFU download. Correct data and retransmit from host.
Paper Motion Flt
The control processor has detected that the paper has failed to
move the required distance after sending a command to the
Paper Drive Motor. Check for paper feed problems. If there
are any paper feed problems, correct them, then press the
Clear key to clear the fault. If there are no paper feed
problems and the condition does not clear, clean or replace the
paper motion sensor. If the message still does not clear,
replace the Controller Board.
Paper Out
Paper is not being detected by the Paper Out sensor. If this
message is correct, refer to the Paper Loading sections in
Chapter 2 of the Operator Manual, then load paper. If the fault
does not clear, clean or replace the paper out sensor. If the
message still does not clear, replace the Controller Board.
Parity Error
Parity is enabled and a mismatch on Bit 8, between the
computer and the printer, has been detected on the currently
active host interface. If there is a mismatch between the
setting of the printer and the setting of he host, you can
change printer parity (see the Config Menu section in Chapter
3 of the Operator Manual). If there is no mismatch between
the printer and host settings, then the data sent from the host
has been corrupted. Retransmit the data from the host. If the
condition repeats, set up the printer for Dump Mode (see the
Config Menu section in Chapter 3), and retransmit the data
again. If you find no errors in the Dump Mode data, replace
the Controller Board.
Platen Calibration Required
This message occurs on power up if the platen sensor has
never been calibrated or the calibration table is found to be
invalid. A valid calibration table adheres to the following
rules: Successive entries in the table must have increasing
sensor values. And the difference between fully open and
fully closed sensor values must be greater than 100.
Содержание 6306
