Talkaphone ETP-CI-4G-V Скачать руководство пользователя страница 3

 

 

ETP-CI-4G-V 

Cellular Interface for Verizon

 

Installation Instructions 

Page 

3

 of 

5

 

 

  Rev. 12/10/2020

 

 

Copyright 2020 Talk-A-Phone, LLC

 

• 7530 North Natchez Avenue • Niles, Illinois 60714 • Phone 773.539.1100 • [email protected] • www.talkaphone.com 

 

All prices and specifications are subject to change without notice. Talk-A-Phone, Talkaphone, Scream Alert, WEBS, and WEBS Contact are registered trademarks of Talk-A-Phone, LLC. 
All rights reserved.  All other trademarks mentioned in this document or website are the property of their respective owners and does not imply or indicate any approval, endorsement, 
sponsorship, or affiliation with such owners unless such approval, endorsement, sponsorship, or affiliation is expressly indicated. 

2.  The rear panel of the 

ETP-CI-4G-V 

Cellular Interface provides the following:

 

 

(1)  Input terminal for 12VDC; 
(2) 

CELL 1

 connector for remote-mounting MIMO antenna; 

(3) 

CELL 2

 connector for remote-mounting MIMO antenna; 

(4) 

GPS

 connector for remote-mounting MIMO antenna; 

(5) 

SIM

 slot for micro-SIM (3FF) card; 

(6) 

CONFIG

 port for a mini-USB connection (for Talkaphone Technical Support purposes only).

 

 

 

 

Figure 3.

  

Rear panel of the 

ETP-CI-4G-V 

Cellular Interface.

 

 

3.  Insert the micro-SIM (3FF) card into the slot labeled 

SIM 

(see 

Figure 3

 

– 

Item 5

). 

 

IMPORTANT:

  The orientation of the micro-SIM card should be angled notch entering the slot first with 

the metal contacts facing down. 

4.  Using a plastic spudger or a small flat head screwdriver, push the micro-SIM card into the slot until a 

click is heard.  To remove the micro-SIM card, push the card until a click is heard and the card springs 
out of the slot. 

5.  Connect the cables from the remote-mounting MIMO antenna to the 

CELL 1, CELL 2, 

and

, GPS 

connecters (see 

Figure 3

 

– 

Items 2, 3, and 4

.  On the built-in cable assembly of the remote-mounting 

MIMO antenna, there are two (2) cables labeled 

CELL

 

– connect those cables to the 

CELL 1

 and 

CELL 2

 connectors.  Any of the two 

CELL 

cables can connect to either connector. 

6.  Connect the ETP-500 Series Phone to the 

PHONE-FXS

 port. 

7.  If the interface is being powered by an SLR Series (solar) kit, connect the 

LOAD

 terminals of the solar 

controller to the appropriate polarity markings on the 

POWER

 terminal (12VDC input) of the 

ETP-CI-

4G-V 

Cellular Interface.  Otherwise, connect a 12VDC power source appropriately with respect to 

polarity. 

8.  Using the built-in mounting flanges, attach the 

ETP-CI-4G-V 

Cellular Interface onto the internal 

mounting panel of the Talk-A-Phone enclosure (e.g., ETP-MTE-W, ETP-MT/R-SOLAR).  The 

ETP-CI-

4G-V

 Cellular Interface should be mounted so that the 12VDC input terminal is on the lower right corner 

(i.e. toward the Earth). 

 

Отзывы: