background image

 

 

 

3

 

 
 
The Flush Time   

 

Defines the duration of the flushing time per station. The following options are selectable: 
 
5-20   sec in steps of 1 sec 
20-55 sec in steps of 5 sec 
1-6     min in steps of 0.5 min 
 
 

The DP Set Point   

 
At  this  field  the  user  defines  the  pres

sure  difference  between  the  filter’s  inlet  and  outlet  that  when 

reached, a flushing cycle will take place. This field is meaningless when electronic DP sensor is not in 
use, therefore the user is expected to define the DP set point to be 00, as a result the actual DP value 
will appear as (- -).  
 
When the pressure is expressed in BAR the range of values is 0.1 

– 2.0 BAR. 

When the pressure is expressed in PSI the range of values is 1- 30 PSI. 
 
When the system does not include the built in electronic DP sensor but uses instead an external DP 
sensor, the flushing request signal arrives in the shape of a closed dry contact at the appropriate input 
terminals.  
 

 
The Flush Mode   

 
The Flush Mode defines how the flushing cycles is triggered. The selectable options are as follows: 
 

OFF

 -   

no flushing will take place  

By time

 

–  

In this case the flushing cycles will be repeated in a selected interval or will be triggered 
by  the  DP  signal  depending  on  what  happens  first.  No  matter  how  was  the  flushing 
cycle  started  the  interval  to  the  next  cycle  will  start  to  be  measured  again  after  each 
ending of a flushing sequence. The selectable intervals are the following: 

 
 

5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60 minutes 

 

2, 3, 4, 5, 6, 8, 12, 18, 24, 72, 120 hours 

 
dp

 

–  

flushing will be triggered by DP only.  

 
 

 
If  the  “+”  and  “-“  keys  are  pressed  and  held  down  simultaneously  the 
“Flush Mode” field will show the left time until next cycle, alternately hours 
and minutes. 

 
 
 

The Accumulations   

 
The unit accumulates and displays the number of flushing cycles caused by DP, by time, or manually 
At each of the accumulation fields, 

the “+” or “-“ keys may be used for clearing the accumulated value. 

 

The Configuration   

 
In  order  to  enter  into  the  configuration  process  press  and  hold  down  the  ENTER  key  for  at  least  3 
seconds. 

REMARK

 

Содержание FILTRON 1-10 AC











Отзывы: