Takuma e-foil jet Скачать руководство пользователя страница 5

/

 38 

EN

/

 38 

By using this product, you agree that you do so at your own risk. TAKUMA does 
not accept any responsibility for personal injury or material damage in the 
case of an accident due to incorrect use.

1.2.3  E-FOIL JET

Do not leave your TAKUMA E-FOIL JET in direct sunlight or moving in the wind 
for long periods of time when not in use. 

Do not leave your TAKUMA E-FOIL JET on hot surfaces such as asphalt or sand 
for long periods of time.

Never leave your TAKUMA E-FOIL JET in an overheated place, such as in a hot 
car. Doing so may cause serious damage.

Do not operate your TAKUMA E-FOIL JET when it is not in the water. Doing so 
will cause it to overheat and may permanently damage the motor.

1.2.4  Jet impeller

Risk of personal injury: 

The TAKUMA E-FOIL JET impeller carries risks of serious and even 
fatal injuries.

Keep body, fingers and toes away from the TAKUMA E-FOIL JET’s 

spinning impeller.
Never start the Jet impeller when out of the water.

Never remove the casing of the jet impeller.

Never touch or handle the jet impeller while the battery is connected. If 
intervention is required on the jet impeller (to remove a foreign body, for 

example), the battery must be removed first.

1.2.5  Electrical parts, batteries and chargers

Before handling the electrical connections of the TAKUMA E-FOIL JET, 
the battery or the chargers, make sure you are in a dry place away 
from water splashes. Never operate in the water or in the presence 
of humidity.
Never open the electrical connectors when your E-FOIL JET is on the 
water.
Never change your battery when your E-FOIL JET is on the water.
Do not attempt to open or modify the electrical parts, battery or 
charger.

Do not use or charge a damaged battery, if it was involved in any 
kind of heavy impact or crash. Doing so can cause the battery to 

catch fire. 

Please contact your local TAKUMA dealer for further assistance.

Signs of a damaged battery:

Loose screws/rivets/connectors
Split or deformed case
Acidic smell
Unusually hot temperature during charging (80°C or more)

Do not disassemble the battery in any way. Water may penetrate causing 

battery to catch fire or explode. 

Do not use other batteries or chargers than those sold by TAKUMA. Any 
damage caused by the use of another battery or charger will not be covered 
by warranty.

Place the battery and the charger in a clean and dry place, out of the reach 
of children under 18 years old.

Keep the battery away from fire, heating sources and out of direct sunlight.

The battery must be used in the temperature range from 0°C to 40°C. Do 
not use or charge the battery at high temperature. Use of the battery in 

environments above 40°C can lead to a fire or an explosion.

Use of the battery below 0°C can lead to permanent damage to the battery.

Содержание e-foil jet






















Отзывы: