1. Notice
Warning
1. Beware of Electric Shock!
2. Once controller is activated, do not touch AC power wiring terminals to avoid electric shock!
3. First to confirm power is OFF, before working on the wiring of controller power supply!
4. Before using this product, please read through this operating manual thoroughly to understand the correct usage based on
the fundamentals of its conten.
5. This product can be used in industrial equipment, working terminal, measurement equipment, but not in life-saving-
related medical equipment.
6. In order to ensure safety even if the temperature controller fails, please set up another alarm system or safety redundancy.
Caution
1. Before the controller transmits power, make sure that the position of the AC power assembly leg is correct. Otherwise,
the controller may be seriously damaged after power transmission is initiated.
2. Before powering on, please confirm whether the power supply voltage is in accordance with the controller's specification
(AC 85~265V or DC 24V.) Otherwise, the controller may be seriously damaged after power transmission is initiated.
3. Check if the wiring is connected to the terminal for the correct terminals (Input, Output.)
4. Please use crimp terminals suitable for M3 screws, as shown below:
3.2mm
3.2mm
Torque : 0.4 N.m (4kgf.cm)
5. Do not install the controller in places subject to high-frequency interference, corrosive gases, and high temperature and
humidity (normal working environment: 0 ~ 50°C, 20 ~ 90% RH.)
6. To avoid noise interference, please keep the sensor wiring away from the power cord and the loading power cord.
7. When the thermocouple lead is extended, please use the compensation lead of the corresponding type to this thermocouple.
8. When the RTD lead wire is extended, please use those with lower resistance value. Please use the same wire between the
three Wires.
2. Order Information
Model
Output 1
Output 2
Alarm
TRS
Remote
COMM
Input type
Power
Accessories
NFY900(Red/Green light)
1
0
1
0
0
0
0
1
A
N
FY901(Blue/White light)
PFY900(Program)
0 None
0
None
0 None
0 None
0 None
0 None
See
input
A
AC 85~265V N None
Range
FY/FU400
48x48mm
1 Relay
1
Relay
1 1 Set
1
4~20mA
1
4~20mA
3
TTL
type
code
D
DC 24V
T
Terminal Cover
m
m
8
4
x
6
9
0
0
6
Y
F
N
FY700/FU72
72x72mm
2 Voltage Pulse
2
Voltage Pulse
2
2 Sets
2
0~20mA
2
0~20mA
B
RS-485
W
IP65
FY800/ FU86
48x96mm
(SSR Drive)
(SSR Drive)
FY900/FU96
96x96mm
3 4~20mA
3
4~20mA
3
3 Sets
A
0~5V
A
0~5V
R
Terminal Cover
PFY400 / FU400
48x48mm
+IP65
PFY600
96x48mm
4 0~20mA
4
0~20mA
B
0~10V
B
0~10V
PFY700 / FU72
72x72mm
PFY800 / FU86
48x96mm
A 0~5V
A
0~5V
C
1~5V
C
1~5V
PFY900 / FU96
96x96mm
B 0~10V
B
0~10V
A
HBA
D
2~10V
D
2~10V
C 1~5V
1~5V
M
Motor valve
C
B
HBA+AL2
control feedback
D 2~10V
D
2~10V
C
HBA+AL2+AL3
Block means optional functions with additional charge
※
5
1 SCR zero cross control
※
HBA : Heater Break Alarm(HBA must use AL1 as alarm relay)
6
3 SCR zero cross control
7
Motor valve control
8
1 SCR phase angle control
※
Boxed-in items are optional functions, which shall incur extra charges.
FY/FU operation manual
4
