background image

 

8

 

TAD Reference One Owner’s Manual

 

Cone-shaped 

spike

Round 

spike

 

Caution: About installation

 

This unit is sold with the understanding that it is to be installed by a properly trained and equipped specialist. 
All matters concerning installation and mounting should be handled by specialists or by your local dealer.

Pioneer waives all responsibility for damages to this unit as the result of improper installation/mounting, 
improper use, remodeling/alteration, and natural disasters.

 

Caution: About the placement of this unit

 

This product weighs 150 kg (330 lb). Make sure that you place this product upon a surface that can easily 
sustain this weight. Additionally, note that when using spikes, each spike supports some 50 kg (110 lb), and as 
such may cause damage to flooring underneath a carpet or other surfaces. To avoid causing such damage, be 
sure to place a sufficiently large and strong cushion underneath each spike.

As a precautionary measure, be sure to not place the unit anywhere where it might fall on a sleeping individual 
in the event of an earthquake.

 

Concerning The Placement Of This Unit

 

There is an aluminum plate attached to the bottom of the unit's cabinet. It can be placed normally upon a flat 
surface. This unit comes with two types of spikes that you can use to adjust the unit to the shape of the floor for 
best possible placement.

We recommend the following placement methods:

For flat surfaces: no spikes

Thick carpet or mat: cone-shaped spikes

Thin carpet or mat: round spikes

INSTALLATION AND PLACEMENT

TAD-R1_En.book 8 ページ 2006年12月4日 月曜日 午後2時42分

Содержание TAD-R1





















Отзывы: