TACKLIFE EMS01A, Руководство пользователя

Страница: 17 / 23

Explanation of the symbols on the equipment 1.
DEAR CUSTOMER,
we hope your new tool brings you much enjoyment and suc- cess.
NOTE:
According to the applicable product liability laws, the manu- facturer of the device does not assume
liability for damages to the product or damages caused by the product that occurs due to:
●
●
●
●
●
●
We recommend:
Read through the complete text in the operating instructions before installing and commissioning the
device.
The operating instructions are intended to help the user to become familiar with the machine and take
advantage of its application possibilities in accordance with the recommenda- tions.
The operating instructions contain important information on how to operate the machine safely, profes-
sionally and economically, how to avoid danger, costly repairs, reduce
downtimes and how to increase reliability and service life of the machine.
In addition to the safety regulations in the operating instruc- tions, you have to meet the applicable
regulations that apply for the operation of the machine in your country.
Keep the operating instructions package with the machine at all times and store it in a plastic cover to
protect it from dirt and moisture. Read the instruction manual each time before operating the machine
and carefully follow its information. The machine can only be operated by persons who were instructed
concerning the operation of the machine and who are informed about the associated dangers. The
minimum age requirement must be complied with.
In addition to the safety instructions contained in this operat- ing manual and the specific regulations of
your country,
the technical rules generally accepted for the operation of machines of the same type must be observed.
We accept no liability for damage or accidents which arise due to non-observance of these instructions
and the safety information.
2.
Introduction
Improper handling,
Non-compliance of the operating instructions,
Repairs by third parties, not by authorized service techni- cians,
Installation and replacement of non-original spare parts,
Application other than specified,
A breakdown of the electrical system that occurs due to the non-compliance of the electric regula-
tions and VDE regula- tions 0100, DIN 57113 / VDE0113.
Device description (fig. 1-21)
3.
●
●
●
●
●
●
●
4.
The sliding compound mitre saw is designed to crosscut wood and plastic respective of the machine’s
size. The sliding cross cut mitre saw is not designed for cutting firewood.
Warning! Do not use the sliding cross cut mitre saw to cut materials other than those specified
described in manual.
Warning! The supplied saw blade is intended exclusively for sawing the following materials:
wood, wood derived products (MDF, chipboard, plywood, blockboard, hardboard, etc.), wood with nails
and 3 mm mild steel plates.
Note: Wood containing non-galvanised nails or screws can also be safely cut when carefully handled.
Note: Do not use the saw blade to cut galvanised materi- als or wood containing galvanised nails. Do
not use the saw blade to saw firewood!
The equipment is to be used only for its prescribed purpose. Any other use is deemed to be a case of
misuse. The user / op- erator and not the manufacturer will be liable for any damage or injuries of any
kind caused as a result of this.
The equipment is to be operated only with suitable saw blades. It is prohibited to use any type of
cutting-off wheel.
To use the equipment properly you must also observe the safety information, the assembly instructions
and the operating instruc- tions to be found in this manual.
All persons who use and service the equipment have to be acquainted with this manual and must be
informed about the equipment’s potential hazards. It is also imperative to observe the accident preven-
tion regulations in force in your area. The same applies for the general rules of health and safety at work.
The manufacturer will not be liable for any changes made to the equipment nor for any damage resulting
from such chang- es. Even when the equipment is used as prescribed it is still im- possible to eliminate
certain residual risk factors. The following hazards may arise in connection with the machine’s construc-
tion and design:
●
●
●
●
Scope of delivery
Sliding compound mitre saw
1 x Clamping device (7) (preassembled)
2 x Workpiece support (8) (preassembled)
Chip collection bag (17)
Allen key 6 mm (C)
Allen key 3 mm (D)
Operating manual
Intended use
Contact with the saw blade in the uncovered saw zone.
Reaching into the running saw blade (cut injuries).
Kick-back of workpieces and parts of workpieces.
Saw blade fracturing.
●
●
●
Please note that our equipment has not been designed for use in commercial, trade or industrial applica-
tions. Our warranty will be voided if the equipment is used in commercial, trade or industrial businesses
or for equivalent purposes.
5.
General safety information for power tools
WARNING! Read all safety warnings, instruc- tions, illustrations and technical data provided
with this power tool. Failure to follow the warnings and in- structions may result in electric shock, fire
and/or serious injury. Save all warnings and instructions for future refer- ence.
The term “power tool” used in the safety instructions refers to mains powered power tools (with power
cord) and cordless power tools (without power cord).
Workplace safety
a)
b)
c)
Electric safety
a)
b)
c)
d)
e)
f)
Personal safety
a)
b)
c)
Catapulting of faulty carbide tips from the saw blade.
Damage to hearing if ear-muffs are not used as necessary.
Harmful emissions of wood dust when used in closed rooms.
Safety information
Keep your workplace clean and well illumi- nated.
Disorderliness and poorly illuminated workplaces may Iead to accidents.
Do not operate the power tool in explosive atmospheres with inflammable liquids, gases or dust.
Power tools generate sparks which may ignite dust or va- pours.
Keep children and other persons away from the power tool during operation.
You may lose control of the tool if you are distracted.
The plug of the power tool must fit into the socket.
Do not modify the plug in any way. Do not use adapter plugs together with grounded power tools.
Unmodified plugs and matching sockets reduce the risk of electric shock.
Avoid body contact with grounded surfaces such as pipes, radiators, ovens and refrigera- tors. There
is an increased risk of electric shock if your body is grounded.
Keep power tools away from rain or humidity. Water permeation into the power tool will increase the
risk of electric shock.
Use the cable solely for its intended purpose. Do not use the cable to carry or hang up the power tool
or to pull out the plug from the socket.
Keep the cable away from heat, oil, sharp edges or mov- ing machine parts. Damaged or twisted
cables increase the risk of electric shock.
When working outdoors with power tools, only use extension cords which are suited for outdoor
areas.
Using extension cords suited for outdoor applications re- duces the risk of electric shock.
lf the operation of power tools in a humid en- vironment cannot be avoided, you must use a residual
current circuit breaker.
The use of a residual current circuit breaker will reduce the risk of electric shock.
Pay attention to what you are doing and use power tools sensibly.
Do not use power tools when you are tired or under the influence of drugs, alcohol or medi- cation. A
single moment of inattention while using pow- er tools may cause severe injury.
Wear personal protective equipment and safe- ty goggles.
Wearing personal protective equipment such as a dust mask, non-skid safety boots, a protective
helmet or hear- ing protection according to the type and application of the power tool reduces the risk
of injury.
Avoid starting the power tool unintentionally. Make sure that the power tool is switched off before you
d)
e)
f)
g)
h)
Use and treatment of the power tool
a)
b)
c)
d)
e)
f)
g)
h)
Service
a)
Warning! This electric tool generates an electromagnetic field during operation. This field can impair
active or passive medi- cal implants under certain conditions. In order to prevent the risk of serious or
deadly injuries, we recommend that persons with medical implants consult with their physician and the
man- ufacturer of the medical implant prior to operating the electric tool.
Safety instructions for mitre saws
a)
connect it to the mains and/or in- sert a battery, pick it up or carry it. lf you have your finger on
the switch when you carry the power tool, or if the machine is switched on when you connect it to the
mains, this may result in accidents.
Remove adjustment tools or wrenches before switching on the power tool.
Tools or wrenches in rotating machine parts may cause injury.
Avoid abnormal body positions.
Stand securely and keep your balance at all times. By doing so, you can control the power tool
more easily in unexpected situations.
Wear suitable clothing. Do not wear loose clothing or jewellery. Keep your hair, cloth- ing and
gloves away from moving parts. Loose clothing, jewellery or long hair may be trapped in moving parts.
lf dust extraction tools or collection bins can optionally be attached, you must make sure that they
are connected and correctly used. Using dust extraction tools may reduce risks caused by dust.
Do not let familiarity gained from frequent use of the tool allow you to become complacent and
ignore tool safety principles. A careless ac- tion can cause severe injury within a fraction of a second.
Do not overload the tool.
Use the appropriate power tool for your type of work. With appropriate power tools, you can work
better and more safely within the given power range.
Do not use the power tool if the switch does not turn it on and off. Any power tool that can- not be
controlled with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or remove the battery pack, if detach- able, from the
power tool before making any adjustments, changing accessories, or storing power tools.
This preventive safety measure reduces the risk of starting the power tool accidentally.
Store idle power tools out of the reach of chil- dren.
Do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
Carefully maintain power tools and accesso- ries.
Check moving parts for proper function and smooth run- ning, and check whether there are parts
which are bro- ken or damaged to the extent that the functionality of the power tool is impaired. Have
damaged parts repaired before using the power tool. Many accidents are caused by poorly-main-
tained power tools.
Keep cutting tools sharp and clean. Carefully maintained cutting tools with sharp edges are less likely
to jam and can be guided more eas- ily.
Use power tools, accessory parts, insertion tools, etc. in compliance with these instruc- tions.
Take into account the working conditions and the activity which is to be carried out. Using power tools
for appli- cations other than those intended may cause dangerous Situations.
Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery han-
dles and grasping surfaces do not allow for safe handling and control of the power tool in unexpected
situations.
Have your power tool repaired by qualified specialists only, and always use original spare parts for
repair. This is to maintain the safety of the power tool.
Use clamps to support the workpiece when- ever possible. If supporting the workpiece by hand,
you must always keep your hand at least 100 mm from either side of the saw blade. Do not use this
saw to cut pieces that are too small to be securely clamped or held by hand. If your hand is placed
b)
c)
d)
e)
f)
g)
h)
i)
j)
k)
l)
m)
n)
o)
p)
q)
r)
too close to the saw blade, there is an in- creased risk of injury from blade contact.
The workpiece must be stationary and clamped or held against both the fence and the table. Do
not feed the workpiece into the blade or cut “freehand” in any way. Unrestrained or moving
workpieces could be thrown at high speeds, causing injury.
Push the saw through the workpiece. Do not pull the saw through the workpiece. To make a
cut, raise the saw head and pull it out over the workpiece without cutting, start the motor, press
the saw head down and push the saw through the workpiece. Cutting on the pull stroke is likely to
cause the saw blade to climb on top of the work- piece and violently throw the blade assembly
towards the operator.
Never cross your hand over the intended line of cutting either in front or behind the saw blade.
Supporting the workpiece “cross handed” i.e. holding the workpiece to the right of the saw blade with
your left hand or vice versa is very dangerous.
Do not reach behind the fence with either hand closer than 100 mm from either side of the saw blade,
to remove wood scraps, or for any other reason while the blade is spinning. The proximity of the
spinning saw blade to your hand may not be obvi- ous and you may be seriously injured.
Inspect your workpiece before cutting. If the workpiece is bowed or warped, clamp it with the
outside bowed face toward the fence. Al- ways make certain that there is no gap be- tween the
workpiece, fence and table along the line of the cut. Bent or warped workpieces can twist or shift
and may cause binding on the spinning saw blade while cutting. There should be no nails or foreign
objects in the workpiece.
Do not use the saw until the table is clear of all tools, wood scraps, etc., except for the work- piece.
Small debris or loose pieces of wood or other ob- jects that contact the revolving blade can be thrown
with high speed.
Cut only one workpiece at a time. Stacked multiple workpieces cannot be adequately clamped or
braced and may bind on the blade or shift during cutting.
Ensure the mitre saw is mounted or placed on a level, firm work surface before use. A level and
firm work surface reduces the risk of the mitre saw becom- ing unstable.
Plan your work. Every time you change the bevel or mitre angle setting, make sure the adjustable
fence is set correctly to support the workpiece and will not interfere with the blade or the guarding
system. Without turning the tool “ON” and with no workpiece on the table, move the saw blade
through a complete simulated cut to assure there will be no interference or danger of cutting the
fence.
Provide adequate support such as table exten- sions, saw horses, etc. for a workpiece that is wider
or longer than the table top. Workpieces longer or wider than the mitre saw table can tip if not se-
curely supported. If the cut-off piece or workpiece tips, it can lift the lower guard or be thrown by the
spinning blade.
Do not use another person as a substitute for a table extension or as additional support. Unsta-
ble support for the workpiece can cause the blade to bind or the workpiece to shift during the cutting
operation pull- ing you and the helper into the spinning blade.
The cut-off piece must not be jammed or pressed by any means against the spinning saw blade.
If confined, i.e. using length stops, the cut-off piece could get wedged against the blade and thrown
violently.
Always use a clamp or a fixture designed to properly support round material such as rods or
tubing. Rods have a tendency to roll while being cut, causing the blade to “bite” and pull the work with
your hand into the blade.
Let the blade reach full speed before contact- ing the workpiece. This will reduce the risk of the
work- piece being thrown.
If the workpiece or blade becomes jammed, turn the mitre saw off. Wait for all moving parts to stop
and disconnect the plug from the power source and/or remove the battery pack. Then work to free the
jammed material. Continued sawing with a jammed workpiece could cause loss of con- trol or
damage to the mitre saw.
After finishing the cut, release the switch, hold the saw head down and wait for the blade to stop
before removing the cut-off piece. Reaching with your hand near the coasting blade is dangerous.
Hold the handle firmly when making an incom- plete cut or when releasing the switch before the saw
Safety Instructions for the handling of saw blades
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
22
Protect yourself and you environment from acci- dents using suitable precautionary measures!
●
●
●
●
●
●
●
●
head is completely in the down posi- tion. The braking action of the saw may cause the saw head
to be suddenly pulled downward, causing a risk of injury.
Do not use damaged or deformed saw blades.
Do not use any insertion tools with cracks. Sort out cracked insertion tools. Repairs are not permit-
ted.
Check the condition of the saw blades before using the sliding compound mitre saw.
Make sure that a suitable saw blade for the material to be cut is selected.
Only use saw blades for which the maximum permissible speed is not lower than the maximum
spindle speed of the sliding compound mitre saw and which are suitable for the material to be cut.
Observe the saw blade direction of rotation.
Only insertion the saw blade if you have mastered their use.
Observe the maximum speed. The maximum speed speci- fied on the insertion tool may not be
exceeded. If specified, observe the speed range.
Clean grease, oil and water off of the clamping surfaces.
Do not use any loose reducing rings or bushes for the reducing of holes on saw blades.
Make sure that fixed reducer rings for securing the inser- tion tool have the same diameter and have
at least 1/3 of the cutting diameter.
Make sure that fixed reducer rings are parallel to each other.
Handle insertion tool with caution. They are ideally stored in the originally package or special
containers. Wear protective gloves in order to improve grip and to further reduce the risk of injury.
Prior to the use of insertion tools, make sure that all protec- tive devices are properly fastened.
Prior to use, make sure that the insertion tool meets the technical requirements of this electric tool
and is properly fastened.
Only use the supplied saw blade for cutting wood, never for the processing of metals.
Only use saw blade diameters in accordance with the markings on the saw.
Use additional workpiece supports, if required for work- piece stability.
Workpiece support extensions must always be secured and used during work.
Replace table inserts when worn! 21 Avoid overheating of the saw teeth.
When sawing plastic, avoid melting of the plastic.
Use the appropriate saw blades for this purpose. Replace damaged or worn saw blades immediately.
When the saw blade overheats, stop the machine. Allow the saw blade to cool down before using the
machine again.
Do not look directly into the laser beam with unprotected eyes.
Never look into the path of the beam.
Never point the laser beam towards reflecting surfaces and persons or animals. Even a laser beam
with a low output can cause damage to the eyes.
Caution - methods other than those specified here can result in dangerous radiation exposure.
Never open the laser module. Unexpected exposure to the beam can occur.
If you do not use the device for a long time, the batteries should be removed.
The laser may not be replaced with a different type of laser.
Repairs of the laser may only be carried out by the laser manufacturer or an authorised representative.
Residual risks
The machine has been built according to the state of the art and the recognised technical safety re-
quirements. However, individual residual risks can arise during operation.
●
●
●
●
●
●
●
●
●
6.
* S1 operating mode, continuous duty
The work piece must have a minimum height of 3 mm and a minimum width of 10 mm.
Make sure that the workpiece is always secured with the clamping device.
Health hazard due to electrical power, with the use of im- proper electrical connection cables.
Furthermore, despite all precautions having been met, some non-obvious residual risks may still
remain.
Residual risks can be minimised if the „safety instructions“ and the „Proper use“ are observed along
with the whole of the operating instructions.
Do not load the machine unnecessarily: excessive pressure when sawing will quickly damage the
saw blade, which re- sults in reduced output of the machine in the processing and in cut precision.
When cutting plastic material, please always use clamps: the parts which should be cut must always
be fixed between the clamps.
Avoid accidental starting of the machine: the operating but- ton may not be pressed when inserting
the plug in an outlet.
Use the tool that is recommended in this manual. In doing so, your machine provides optimal perfor-
mance.
Hands may never enter the processing zone when the ma- chine is in operation.
Release the handle button and switch off the machine prior to any operations.
Technical data
Noise
Total noise values determined in accordance with EN 62841.
Sound pressure level LpA 97,2 dB(A)
Uncertainty KpA 3 dB
Sound power level LWA 110,2 dB(A)
Uncertainty KWA 3 dB
Wear hearing protection.
The effects of noise can cause a loss of hearing
The above-mentioned noise emission values were measured in accordance with a standardised test
procedure and can be used to compare one power tool with another.
The above-mentioned noise emission values can also be used for the preliminary assessment of
exposure.
Warning:
●
●
7.
●
●
●
●
●
ATTENTION
The device and packaging materials are not toys! Children must not be allowed to play with plastic bags,
film and small parts! There is a risk of swal- lowing and suffocation!
●
●
●
●
●
●
●
●
7.1
The saw blade guard protects against accidental contact with the saw blade and from chips flying
around.
Check function
To do so, fold the saw downwards:
●
The noise emissions during the actual use of the power tool may differ from the above-mentioned
values depending on the power tool being used, in particular on the type of work- piece being
processed.
Try to keep emissions as low as possible, for example by limiting your working time. In this regard,
all the operational cycle phases must be taken into consideration (such as the times when the tool is
switched off or running idle).
Before starting the equipment
Open the packaging and remove the device carefully.
Remove the packaging material as well as the packaging and transport bracing (if available).
Check that the delivery is complete.
Check the device and accessory parts for transport dam- age.
If possible, store the packaging until the warranty period has expired.
The equipment must be set up where it can stand securely. Secure the machine on a workbench or
a base frame with 4 screws (not included in delivery) using the holes on the fixed saw table (15).
Pull out the pre-installed tilt protection (36) completely and secure it with an Allen key (D).
Adjust the adjusting screw (37) to the level of the tabletop to avoid wobbling of the machine.
All covers and safety devices have to be properly fitted be- fore the equipment is switched on.
It must be possible for the blade to run freely.
When working with wood that has been processed before, watch out for foreign bodies such as nails
or screws, etc.
Before you press the ON/OFF switch check that the saw blade is fitted correctly. Moving parts must
run smoothly.
Before you connect the equipment to the power supply make sure the data on the rating plate are
dentical to the mains data.
Checking the moving saw blade guard safety device (5)
The saw blade guard must provide free access to the saw blade without touching other parts.
●
8.
8.1
●
●
●
●
●
●
●
8.2
●
●
●
●
●
●
●
●
8.3
In the case of cutting widths up to approx. 100 mm it is possible to fix the traction function of the saw with
the set screw (20) in the rear position. In this position the machine can be operated in cross cutting
mode. If the cutting width is over 100 mm then it is necessary to ensure that the set screw (20) is loose
and the machine head (4) can move.
Attention! For 90° crosscuts, the moveable stop rail (16a) must be fixed in the inner position.
●
●
●
●
●
●
●
●
●
When folding the saw upwards into the starting position, the saw blade guard must cover the saw
blade automati- cally.
Attachment and operation
Attaching the sliding compound mitre saw (fig.1/2/4/5)
In order to adjust the rotary table (14), fold the locking han- dle (11) upwards and pull up the latched
position lever (35) with your index finger.
Turn the rotary table (14) and pointer (12) to the desired angle measurement of the scale (13). To fix
the setting, fold the locking handle (11) downwards.
Pressing the machine head (4) lightly downwards and re- moving the locking bolt (23) from the motor
bracket at the same time disengages the saw from the lowest position.
Swing the machine head (4) up.
It is possible to secure the clamping devices (7) to the left or right on the fixed saw table (15). Insert
the clamping devices (7) in the holes on the rear side of the stop rail (16) and secure it with the star
grip screws (7a).
For 0°- 45° mitre cuts, the clamping device (7) must only be mounted on the right side (see fig.
11-12).
It is possible to tilt the machine head (4) a max. 45° to the left by loosening the set screw (22).
Workpiece supports (8) must always be secured and used during work. Set the desired table size by
loosening the set screw (9). Then tighten the set screw (9) again.
Precision adjustment of the stop for crosscut 90° (fig. 1/2/5/6)
No stop angle included.
Lower the machine head (4) and secure it using the locking bolt (23).
Loosen the set screw (22).
Position the angle stop (A) between the saw blade (6) and the rotary table (14).
Loosen the lock nut (26a).
Adjust the adjusting screw (26) until the angle between the saw blade (6) and rotary table (14) is 90°.
Re-tighten the lock nut (26a).
Subsequently check the position of the angle indicator. If necessary loosen the pointer (19) using a
Philips screwdriv- er, set to position 0° on the angle scale (18) and re-tighten the retaining screw.
Crosscut 90° and turntable 0° (fig. 1/2/7)
Open the set screw (16b) for the moveable stop rail (16a) and push the moveable stop rail (16a)
inwards.
The moveable stop rail (16a) must be locked in a position far enough from the inner position that the
distance between the stop rail (16a) and the saw blade (6) is no more than 8 mm.
Before making the cut, check that the stop rail (16a) and the saw blade (6) cannot collide.
Re-tighten the set screw (16b).
Move the machine head (4) to its upper position.
Use the handle (1) to push back the machine head (4) and fix it in this position if required (dependent
on the cutting width).
Place the piece of wood to be cut at the stop rail (16) and on the turntable (14).
Lock the material with the clamping devices (7) on the fixed saw table (15) to prevent the material
from moving during the cutting operation.
Release the lock switch (3) and press the ON/OFF switch(2) to start the motor. (Refer also to point
8.13 “Changing the speed” in this regard.)
●
●
●
8.4
The sliding compound mitre saw can be used to make crosscuts of 0° -45° to the left and 0° -45° to the
right in relation to the stop rail.
Important! For 90° crosscuts, the moveable stop rail (16a) must be fixed in the inner position.
●
●
●
●
●
●
●
●
8.5
●
●
●
Attention! For mitre cuts (inclined saw head), the left side of the moveable stop rails (16a) must be fixed
in the outer posi- tion.
●
●
●
●
●
●
●
●
●
8.6
The sliding compound mitre saw can be used to make mitre cuts of 0° - 45° in relation to the work face.
Attention! For mitre cuts (inclined saw head), the left side of the moveable stop rails (16a) must be fixed
With the drag guide (21) fixed in place (21):
use the handle (1) to move the machine head (4) steadily and with light pressure downwards until the
saw blade (6) has completely cut through the work piece.
With the drag guide (21) not fixed in place (21): pull the machine head (4) all the way to the front.
Lower the handle (1) to the very bottom by applying steady and light downward pressure. Now push
the machine head (4) slowly and steadily to the very back until the saw blade (6) has completely cut
through the work piece.
When the cutting operation is completed, move the machine head back to its upper (home) position
and release the ON/ OFF button (2).
Attention! The machine executes an upward stroke auto- matically due to the return spring, i.e. do
not release the han- dle (1) after completing the cut; instead allow the machine head to move
upwards slowly whilst applying light counter pressure.
Crosscut 90° and turntable 0° - 45° (fig. 1/7/8)
Open the set screw (16b) for the moveable stop rail (16a) and push the moveable stop rail (16a)
inwards.
The moveable stop rail (16a) must be fixed far enough in front of the innermost position that the
distance between the stop rail (16a) and the saw blade (6) amounts to a minimum of 8 mm.
Before making the cut, check that the stop rail (16a) and the saw blade (6) cannot collide.
Secure the set screw (16b) again.
Loosen the locking handle (11) if tightened, pull up the latched position lever (35) with your index
finger and use the locking handle (11) to set the rotary table (14) to the desired angle.
The pointer (12) on the rotary table must match the desired angle on the scale (13) on the fixed saw
table (15).
Re-tighten the locking handle (11) to secure the rotary table (14).
Cut as described under section 8.3.
Precision adjustment of the stop for mitre cut 45° (fig. 1/2/5/9/10)
No stop angle included.
Lower the machine head (4) and secure it using the locking bolt (23).
Fix the rotary table (14) in the 0° position.
Open the set screw (16b) for the moveable stop rail (16a) and push the moveable stop rail (16a)
outwards.
The moveable stop rail (16a) must be fixed far enough in front of the innermost position that the
distance between the stop rail (16a) and the saw blade (6) amounts to a maxi- mum of 8 mm.
The right side of the moveable stop rails (16a) must be in the inner positiion.
Before making a cut, check that the stop rail (16a) and the saw blade (6) cannot collide.
Loosen the set screw (22) and use the handle (1) to angle the machine head (4) 45° to the left.
45° - position angle stop (B) between the saw blade (6) and rotary table (14).
Loosen the lock nut (27a) and adjust the adjustment screw(27) until the angle between the saw blade
(6) and the ro- tary table (14) is precisely 45°.
Re-tighten the lock nut (27a).
Subsequently check the position of the angle indicator. If necessary, loosen the pointer (19) using a
Philips screwdriv- er, set to position 45° on the angle scale (18) and re-tighten the retaining screw.
Mitre cut 0°- 45° and turntable 0° (fig. 1/2/11)
in the outer posi- tion.
●
●
●
●
●
●
●
●
●
●
8.7
The sliding compound mitre saw can be used to make mitre cuts to the left of 0°- 45° in relation to the
work face and, at the same time, 0° - 45° to the left or 0° - 45° to the right in relation to the stop rail
(double mitre cut).
Attention! For mitre cuts (inclined saw head), the left side of the moveable stop rails (16a) must be fixed
in the outer position.
●
●
●
●
●
●
●
●
●
●
●
●
8.8
●
●
8.9
The saw is equipped with a debris bag (17) for sawdust and chips. Attention! The chip collection bag
may only be used when cutting wood and wood-like materials!
Squeeze together the metal ring on the dust bag and attach it to the outlet opening in the motor area.
The debris bag (17) can be emptied by means of a zipper at the bottom.
Connection to an external dust extractor
For dust extraction, a vacuum hose can also be connected to the dust extraction spout.
●
●
Open the set screw (16b) for the moveable stop rail (16a) and push the moveable stop rail (16a)
outwards.
The moveable stop rail (16a) must be fixed far enough in front of the innermost position that the
distance between the stop rail (16a) and the saw blade (6) amounts to a minimum of 8 mm.
The right side of the moveable stop rails (16a) must be in the inner positiion.
Before making a cut, check that the stop rail (16a) and the saw blade (6) cannot collide.
Secure the set screw (16b) again.
Move the machine head (4) to the top position.
Fix the rotary table (14) in the 0° position.
Loosen the set screw (22) and use the handle (1) to angle the machine head (4) to the left, until the
pointer (19) indi- cates the desired angle measurement on the scale (18).
Re-tighten the set screw (22).
Cut as described in section 8.3.
Mitre cut 0°- 45° and turntable 0°- 45° (fig. 2/4/12)
Open the set screw (16b) for the moveable stop rail (16a) and push the moveable stop rail (16a)
outwards.
The moveable stop rail (16a) must be fixed far enough in front of the innermost position that the
distance between the stop rail (16a) and the saw blade (6) amounts to a minimum of 8 mm.
Before making a cut, check that the stop rail (16a) and the saw blade (6) cannot collide.
Re-tighten the set screw (16b).
Move the machine head (4) to its upper position.
Fold the locking handle (11) upwards to loosen the rotary table (14).
Set the rotary table (14) to the desired angle (refer also to point 8.4 in this regard).
Fold the locking handle (11) downwards to secure the rotary table (14).
Undo the set screw (22).
Use the handle (1) to tilt the machine head (4) to the left until it coincides with the required angle
value (in this connection see also section 8.6).
Re-tighten the set screw (22).
Cut as described under section 8.3.
Limiting the cutting depth (fig. 3/13)
The cutting depth can be infinitely adjusted using the screw (24). To do this loosen the knurled nut
(24a) on the screw (24). Turn the screw (24) in or out to set the required cutting depth. Then re-tight-
en the knurled nut (24a) on the screw (24).
Check the setting by completing a test cut.
Chip collection bag (fig. 1/20)
Connect the vacuum hose with the dust extraction spout.
The industrial vacuum cleaner must be suitable for the mate- rial being worked.
●
8.10
Important!
Wear safety gloves when changing the saw blade. Risk of injury!
●
●
●
●
●
●
●
●
●
●
●
●
●
8.11
If the laser (32) ceases to indicate the correct cutting line, you can readjust the laser. Loosen the Philips
head screws (E) and set the laser by moving sideways until the laser beam strikes the teeth of the saw
blade (6).
Firmly secure both screws (E).
8.12
The mitre saw has 2 speed ranges:
●
●
9.
●
●
●
●
●
10.
Warning! Prior to any adjustment, maintenance or service work disconnect the mains power plug!
General maintenance measures
Wipe chips and dust off the machine from time to time using a cloth. In order to extend the service life of
the tool, oil the rotary parts once monthly. Do not oil the motor.
When cleaning the plastic do not use corrosive products. Cleaning the moving saw blade guard safety
device (5)
Always check the saw blade guard for debris before using the machine.
Remove old sawdust and splinters using a brush or similar tool.
When vacuuming dust that is especially detrimental to health or carcinogenic, use a special vacuum
cleaner.
Changing the saw blade (fig. 1/2/14-16) Remove the power plug!
Swing the machine head (4) upwards and lock with the lock- ing bolt (23).
Fold the saw blade guard (5) upwards.
Use one hand to insert the Allen key (C) in the flange screw (28).
Firmly press the saw shaft lock (30) and slowly rotate the flange screw (28) in clockwise direction. The
saw shaft lock(30) engages after no more than one rotation.
Now, using a little more force, slacken the flange screw (29) in the clockwise direction.
Turn the flange screw (28) right out and remove the outer flange (29).
Take the blade (6) off the inner flange (31) and pull out downwards.
Carefully clean the flange screw (28), outer flange (29) and inner flange (31).
Fit and fasten the new saw blade (6) in reverse order.
Important! The cutting angle of the teeth, in other words the direction of rotation of the saw blade (6)
must coincide with the direction of the arrow on the housing.
Before continuing your work make sure that all safety de- vices are in good working condition.
Important! Every time that you change the saw blade (6), check to see that it spins freely in the table
insert (10) in both perpendicular and 45° angle settings.
Important! The work to change and align the saw blade (6) must be carried out correctly.
Adjusting the laser (fig. 18)
Changing the speed (fig. 17)
To operate the mitre saw at a speed of 3200 rpm (metal), set the speed regulation switch (34) to
position I.
To operate the saw at a speed of 5000 rpm (wood), set the speed regulation switch (34) to position II.
Transport
Tighten the locking handle (11) to lock the rotary table.
Press the machine head (4) downwards and secure with the locking bolt (23).
Fix the saw’s drag function with the locking screw for drag guide (20) in rear position.
Carry the equipment by the fixed saw table (15).
When reassembling the equipment proceed as described under section 7.
Maintenance
Replacing the table insert Danger!
With a damaged table insert (10) there is a risk of small parts getting stuck between table insert and saw
blade, blocking the saw blade.
Immediately replace damaged table inserts!
1.
2.
3.
4.
Brush inspection (fig. 19)
Check the carbon brushes after the first 50 operating hours with a new machine, or when new brushes
have been fitted. After carrying out the first check, repeat the check every 10 operating hours.
If the carbon is worn to a length of 6 mm, or if the spring or contact wire are burned or damaged, it is
necessary to replace both brushes. If the brushes are found to be usable following removal, it is possible
to reinstall them.
When servicing the carbon brushes, open the two latches coun- terclockwise (as shown in figure 19).
Then remove the carbon brushes. Replace the carbon brushes in the reverse order.
11.
Store the device and its accessories in a dark, dry and frost- proof place that is inaccessible to children.
The optimum stor- age temperature is between 5 and 30˚C.
Store the electrical tool in its original packaging.
Cover the electrical tool in order to protect it from dust and moisture.
Store the operating manual with the electrical tool.
12.
The electrical motor installed is connected and ready for operation. The connection complies with the
applicable VDE and DIN provisions.
The customer‘s mains connection as well as the ex- tension cable used must also comply with these
regulations.
●
●
●
●
Important information
In the event of an overloading the motor will switch itself off. After a cool-down period (time varies) the
motor can be switched back on again.
Damaged electrical connection cable.
The insulation on electrical connection cables is often dam- aged.
This may have the following causes:
●
●
●
●
Remove screws at table insert. If required, turn rotary table and incline saw head to be able to reach
the screws.
Remove table insert.
Install new table insert.
Tighten the screws at table insert.
Storage
Electrical connection
The product meets the requirements of EN 61000-3-11 and is subject to special connection
conditions. This means that use of the product at any freely selectable connection point is not allowed.
Given unfavourable conditions in the power supply the prod- uct can cause the voltage to fluctuate
temporarily.
The product is intended solely for use at connection points that a)do not exceed a maximum permitted
supply impedance “Z” (Zmax = 0.382 Ω), or b)have a continuous current-carrying capacity of the
mains of at least 100 A per phase.
As the user, you are required to ensure, in consultation with your electric power company if necessary,
that the connec- tion point at which you wish to operate the product meets one of the two require-
ments, a) or b), named above.
Passage points, where connection cables are passed through windows or doors.
Kinks where the connection cable has been improperly fas- tened or routed.
Places where the connection cables have been cut due to being driven over.
Insulation damage due to being ripped out of the wall out- let.
●
Such damaged electrical connection cables must not be used and are life-threatening due to the insula-
tion damage.
Check the electrical connection cables for damage regularly. Make sure that the connection cable does
not hang on the power network during the inspection.
Electrical connection cables must comply with the applicable VDE and DIN provisions. Only use
connection cables with the marking „H05VV-F“.
The printing of the type designation on the connection cable is mandatory.
AC motor:
The mains voltage must be 220 - 240 V~.
●
Connections and repairs of electrical equipment may only be carried out by an electrician.
Please provide the following information in the event of any enquiries:
●
●
13.
The equipment is supplied in packaging to prevent it from be- ing damaged in transit. The raw materials
in this packaging can be reused or recycled. The equipment and its accesso- ries are made of various
types of material, such as metal and plastic. Defective components must be disposed of as special
waste. Ask your dealer or your local council.
Old devices must not be disposed of with house- hold waste!
Improper handling of waste equipment may have negative consequences for the environment and
human health due to potentially hazardous substances that are often contained in electrical and
electronic equipment. By properly disposing of this product, you are also contributing to the effective use
of natural resources. You can obtain information on collection points for waste equipment from your
municipal administration, public waste disposal authority, an author- ised body for the disposal of waste
electrical and electronic equipment or your waste disposal company.
Cracks due to the insulation ageing.
Extension cables up to 25 m long must have a cross-section of 1.5 mm2.
Type of current for the motor
Machine data - type plate
Disposal and recycling
14.Troubleshooting
Service information
Please note that the following parts of this product are subject to normal or natural wear and that the
following parts are therefore also required for use as consumables.
Wear parts*: carbon brushes, saw blade, table inserts, sawdust bags
* Not necessarily included in the scope of delivery!
- 12 -