manualshive.com logo in svg

TA Service TA iQ, Руководство по обслуживанию, Страница: 12 / 50

Поделиться
Скачать
TA Service TA iQ Скачать руководство пользователя страница 12

 

 

 

Page 12

 

 

 

 

Brake Lamp Short  

This occurs when the control system detects a short in the Brake Lamp Circuit.  
• Check the brake lamps, cables and connections to the control system.  
If the trip is still present after the above checks have been made, then the ISM may be defective.  
 

Lamp Short  

This occurs when the control system detects a short in either of the Lamp Circuits.  
7205 - Left Lamp Short  
7209 - Right Lamp Short  
• Check the lamps, cables and connections to the control system.  
If the trip is still present after the above checks have been made, then the ISM may be defective.  
 

Indicator Lamp Short  

This occurs when the control system detects a short in either of the Indicator Circuits.  
7206 - Left Indicator Short  
720A - Right Indicator Short  
• Check the indicators, cables and connections to the control system.  
If the trip is still present after the above checks have been made, then the ISM may be defective.  
 

Indicator Lamp Failed  

This occurs when the control system detects a failure in either of the Indicator Circuits. This is most likely to be an indicator bulb failure. 7207 - Left 
Indicator Failed  
7208 - Right Indicator Failed  
• Check the indicator bulbs, cables and connections to the control system.  
If the trip is still present after the above checks have been made, then the ISM may be defective.  
 

Over-current  

This occurs when the control system detects an excessive amount of current in an Actuator Channel.  
This may be due to a faulty endstop switch, actuator motor, cables or connections.  
• Check the movement of the actuator is not obstructed.  

• Check the endstop switches (if fitted) are terminating the power to the actuator motor.  
If the trip is still present after the above checks have been made, then the SM or ISM may be defective.  
 

Overtemp (acts)  

This occurs when the control system detects that the SM or ISM’s actuator circuitry has become too hot. The control system will cease drive to the 
actuator motor in question.  
• Allow the SM or ISM to cool.  

• If the SM or ISM is frequently overheating check the condition of the actuator motors and the connections to them.  

• If the trip persists contact TA Service or your service agent.  
 

Overtemp (lamps)  

This occurs when the control system detects that the ISM’s lighting circuitry has become too hot. The control system will cease supplying current to 
the lamp in question.  
• Allow the ISM to cool.  

• If the ISM is frequently overheating check the condition of all the connected bulbs and lamps.  

• If the trip persists contact your service agent.  
 

DIME Error  

This occurs when the control system detects an identification conflict between two modules in the system.  
If a new module has been introduced:  
• Disconnect the new module and cycle the power.  

• If no trip is present connect the new module to the system and cycle the power.  

• If the trip reappears then the new module must be the cause of the problem.  
 
If there have been no additions:  
• Disconnect one module at a time and cycle the power.  
 
If the trip is still present after the above checks have been made, contact TA Service or your service agent.  
 

Содержание TA iQ



















































Отзывы:

Нет отзывов