background image

6

©

 

Copyright 2006 TAC All Rights Reserved.

F-24853-4

4-20 mA Inputs

Any of the universal analog inputs may also be configured as 
a 4-20 mA current signal input, as shown in Figure-6.

When configured as a 4-20 mA input, an externally powered 
device must be used. The MPC-8AI does not provide panel 
power.

Figure-4 4-20 mA Wiring Information.

Table-3 illustrates the numbering scheme and software 
assignments of the eight 4-20 mA analog inputs. When 
making these assignments, the first entry is the option slot 
number on the connected MSC-MPC controller and the 
second entry is the number of the analog input being used. 
For example, when plugged into option slot number 2, analog 
input number 1 has an assignment of AI 21.

Table-3 Software Assignments for 4-20 mA Analog Input.

INPNT = AI# (as shown below) /NOT

Note: To calculate SCALE and OFSET for these devices, 
use the MOCALC instructions covered previously in this 
document.

Contact Inputs

Any of the universal inputs on the MPC-8AI is capable of 
monitoring a single normally open or normally closed contact 
input (excluding pulse inputs). This input utilizes a 1K ohm, 
1%, 1/4-watt supervision resistor installed with the input 
device. The device is terminated to the appropriate AI 
connector terminals.

When Configured as a Normally Open Contact Input

Figure-5 Normally Open Contact Input Wiring Information.

Conditions are as follows:

STOP

when contact is open

RUN

when contact is closed

TROUBLE

when conductor is open

The software assignment required for the corresponding 
hardware address of the selected contact input is shown in 
Table-4 below.

Table-4 Assignments for AIs used as Normally Open 

Input.

INPNT = AI# (as shown below) /REV/RUN

Option Slot # On The MSC-MPC Controller

AI#

1

2

3

4

AI1

AI 11

AI 21

AI 31

AI 41

AI2

AI 12

AI 22

AI 32

AI 42

AI3

AI 13

AI 23

AI 33

AI 43

AI4

AI 14

AI 24

AI 34

AI 44

AI5

AI 15

AI 25

AI 35

AI 45

AI6

AI 16

AI 26

AI 36

AI 46

AI7

AI 17

AI 27

AI 37

AI 47

AI8

AI 18

AI 28

AI 38

AI 48

SCALE

OFSET

CVTYP

20

0

LIN H

Option Slot # On The MSC-MPC Controller

AI#

1

2

3

4

AI1

AI 11

AI 21

AI 31

AI 41

AI2

AI 12

AI 22

AI 32

AI 42

AI3

AI 13

AI 23

AI 33

AI 43

AI4

AI 14

AI 24

AI 34

AI 44

AI5

AI 15

AI 25

AI 35

AI 45

AI6

AI 16

AI 26

AI 36

AI 46

AI7

AI 17

AI 27

AI 37

AI 47

AI8

AI 18

AI 28

AI 38

AI 48

Содержание MPC-8AI









Отзывы: