SyxthSense SYX66 Series Скачать руководство пользователя страница 6

Страница: 6 / 61

SYX66x Commissioning Guide

V1.10.3 300117

Page 6 of 61

1.3

INPUTS

Six temperature sensor inputs and two digital Inputs are available and are to be used as follows.

The sensor characteristic type to be used is dictated by the controller part number:

Terminal Pin

Function

Details

13&15

Pin 1

Outside Air Temperature

Sensor Part:

TEU

•

Outside economy

•

Compensation

•

Frost protection

14&15

Pin 2

Compensator Flow Sensor

Sensor Part:

TEAT Immersion

or TEP Strap-On

•

Heating

Valve

Compensation

Control

16&15

Pin 3

Boiler/Heating Return Sensor

Sensor Part:

TEAT Immersion

or TEP Strap-On

•

Return Pipe Frost protection

(Optional but strongly
recommended)

17&15

Pin 4

Boiler Flow Sensor

Sensor Part:

TEAT Immersion

or TEP Strap-On

•

One or two boiler control

•

Boiler compensation

•

Boiler high temperature alarm and
boiler cut out

31&33
32&33

Pin 5

Pin 6

Space Sensor 1

Space Sensor 2

Sensor Part:

TEHR

•

Optimum Start/Stop

•

Averaging (when 2 used)

•

Day economy

•

Room Influence

•

Space Frost protection

27&28

Pin 9

Remote Day Extend button for
heating (and HWS if selected)

LAP5

•

Closed contact extends the time
schedule for as long as the contact
is closed. Heating controls to day
requirements as required, or not.

29&30

Pin 10

Auxiliary Switch Input

(Close switch to activate)

•

Multi-function input

•

Installer can select

one

of the

following uses :

1.Frost Mode (Holiday Switch)

2.HWS Demand (Boiler Set point Request)

3.Summer Switch

4.Underfloor Heat Demand

Special Note:

KP10 sensors used with the SYX660 controller are polarity sensitive. The sensors have a +ve and

–

ve connection.

When connecting these sensors to the SYX660 please connect

–

side of the sensor to terminals

and use

the +ve to the remaining connection as stated above. Other controller types and their sensors are not polarity
sensitive and so have no requirement for special attention.

Содержание SYX66 Series






























































Результаты поиска

Содержание SYX66 Series

Отзывы:

Похожие инструкции для SYX66 Series

Бренды по названию

Популярные бренды

SyxthSense SYX66 Series, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание SYX66 Series

Отзывы:

Похожие инструкции для SYX66 Series

Бренды по названию

Популярные бренды