SystemAir SYSHRW 096 Скачать руководство пользователя

Страница: 20 / 46

English

18 SysHrw

VERY IMPORTANT:

3N~400V-50HZ

The outdoor unit is equipped as standard with a phase sequence and cut-out controller located in the

electrical box.

THIS PRODUCT IS EQUIPPED WITH A PHASE SEQUENCE CONTROLLER. THE LED’s INDICATE THE FOLLOWING

CONDITIONS:

Green LED = 1
Yellow LED =1

Low voltage supply
The compressor rotation

direction is correct

Green LED = 1

Yellow LED =0

Phase inversion or phase

absent (L1)
The compressor and the

fans do not start.

Green LED = 0

Yellow LED =0

Phase absent (L2 or L3)
the compressor and the

fans do not start.

13.2.5. SETTING OF THERMAL PROTECTION AND FUSES

MODELS thermal relay

FT3

Magneto-thermal

trip switch

FF7

FF2 Fuse

/gG type

400V

096

2.6 A

2 A

25 A gG

120

3.4 A

2 A

32 A gG

14. ELECTRICAL CONNECTIONS

14.1. GENERALITIES

Ensure that the available electrical power supply and the network frequency are matched to the required

operating current, taking account of the appliance’s specific location and the current required to supply any

other appliances connected to the same circuit.

1. Ensure that the unit is supplied with the specified voltage. Two stuffing boxes and one grommet hole

are provided on the side of the appliance. They are used respectively for the power and the control

wiring. The power supply line must be properly dimensioned with a motor supply type fuse or a

mains circuit breaker to protect the circuit against voltage surges. (Refer to the Maker’s Plate for the

voltages to be taken into consideration).

2. The electrical power supply three-phase 400V/3ph/50Hz must comprise a neutral to feed the control

circuit.

3. Always shut down the power supply to the unit before connecting the thermostat wiring.

Содержание SYSHRW 096















































Результаты поиска

Содержание SYSHRW 096

Отзывы:

Похожие инструкции для SYSHRW 096

Бренды по названию

Популярные бренды

SystemAir SYSHRW 096, Руководство по установке и обслуживанию

Результаты поиска

Содержание SYSHRW 096

Отзывы:

Похожие инструкции для SYSHRW 096

Бренды по названию

Популярные бренды