SystemAir FGT010 Скачать руководство пользователя

Страница: 125 / 143

15.

Possible alarms of additional electric heater

Before the start up, there will be an alarm because we do not have Terminal 3 and 4 from the electric

heater connected to the Terminals 29 and 30 in the electrical cabinet.

If we have connected the terminals then the reason is that maybe we forgot to configure to NC

contact in the menu:

If the alarm is active when the unit is running for some time, there will be an error electric heating is

overheated.

If the screen shows (picture bellow) the alarm ''Returned'', this means that the fault was removed

but the alarm was not confirmed. There was too hot in area of electric heater and automatic

thermostat disconnect power supply to contactor. Solution is that you need to increase airflow in

case if you have set point under minimum airflow:

To confirm an alarm press OK button and enter the password ''1111'' and ''Acknowledge''.

If the alarm is active and there is no ''Returned'' written then is probably still too hot in area of

electric heater. Wait 15min and if sign ''Returned'' appear then use solution from above.

If there is still alarm active after 15min then is probably triggered manual thermostat and its need to

be reset manually. If manual thermostat is OK and it’s still alarm then is something wrong with the

wire connection between terminal 29 and 30 from electric cabinet to terminal 3 and 4 to electric

heater.

DO NOT SET THE ALARM TO ''BLOCK'' STATUS

whit this we block alarm. When an error will appears

in system, it will not be displayed. This will possible damaged the system and the components or

there could be a fire outbreak!

Содержание FGT010
















































































































































Результаты поиска

Содержание FGT010

Отзывы:

Похожие инструкции для FGT010

Бренды по названию

Популярные бренды

SystemAir FGT010, Инструкция по эксплуатации

Результаты поиска

Содержание FGT010

Отзывы:

Похожие инструкции для FGT010

Бренды по названию

Популярные бренды