D900-38-00
3
I56-2477-002R
Mounting
Reversible strobe module
Should the back box be located near an obstruction such as a
doorway, the strobe module is field-reversible (Fig. 1).
Figure 4: Surface mount back box – 4
″
Figure 3: Mounting to irregular surfaces
LOCKING RIB SLOT
DRYWALL SCREWS
(OPTIONAL)
A0168-00
4-INCH BACK BOX
MUD RING
8-32 SCREW
6-32 SCREW
6-32 SCREW
8-32 SCREW
BBS-CHS
A0169-00
Flush mount back box
The chime/strobe can be flush mounted on a 4
″×
4
″×
1
1
⁄
2
″
back box
(Fig. 2) as follows:
A. For the 4
″×
4
″
, mount the mud plate (provided) using the 8-32
pan head screws. Make sure the mud ring is mounted verti-
cally, as shown.
B. Mount the chime/strobe using the 6-32 oval head screws. The
chime/strobe shall be mounted on the left side of the mud
ring. The 6-32 screws shall be inserted into the holes on the
mud ring that are opposite that of the strobes; i.e., when the
strobe is on the right, screws into the left side of the mud ring,
and vice versa. See Figure 1.
NOTE:
Two drywall screws (provided) may be used to fasten the
mounting plate to the wall. To use the drywall screws,
it will be necessary to first unsnap and hinge the strobe
module away from the mounting plate. (Fig. 3)
Surface mount back box
The chime/strobe can be surface mounted on a 4
″×
4
″×
1
1
⁄
2
″
back
box (Fig. 4) as follows:
A. Mount the BBS-CHS and the mud ring (provided) using the
8-32 pan head screws. Make sure that the large opening in the
BBS-CHS lines up with the horn and the mud plate is mounted
vertically, as shown.
B. Mount the chime/strobe using the 6-32 oval head screws. The
chime/strobe shall be mounted on the left side of the mud
ring. The 6-32 screws shall be inserted into the holes on the
mud ring that are opposite that of the strobes; i.e., when the
strobe is on the right, screws into the left side of the mud ring,
and vice versa. See Figure 1.
To reverse the strobe module: insert screwdriver, as shown in
Fig. 3, to unlock snap. While pushing in the screwdriver, pull
back on the strobe module. Hinge the strobe module, disengage
the Locking Rib and lift the module away from the mounting
plate. Turn the module so that it is upside down from its original
position, re-insert the module into the mounting plate (be sure
to insert the Locking Rib into the slot), and press the module
into the mounting plate. The strobe module will make a “click”
when it has locked into place. Turn the entire assembly so that
the lens/reflector is on the bottom, as shown. The unit can now
be mounted.
INSERT
SCREWDRIVER
TO REMOVE
LOCKING RIB
When strobe is on the
right, mount chime/strobe
with 6-32 screws inserted
into the holes on the left
of the mud ring.
LEFT
RIGHT
When strobe is on the
left, mount chime/strobe
with 6-32 screws inserted
into the holes on the right
of the mud ring.
LEFT
RIGHT
A0166-00
Viewing Window
Figure 5: Candela Selections
For strobe candela selection, adjust slide switch
located on the rear of the product while watching
the viewing window on the side of the reflector.
A0133-00
Figure 1: Reversible strobe module
4-INCH BACK BOX
MUD RING
8-32 SCREW
6-32 SCREW
A0167-00
Figure 2: Flush mount back box – 4
″
