LA700-01-01
I56-3746-000
Pittway Tecnologica Srl, Via Caboto 19/3, 34147 Trieste, Italy
MANUTENÇÃO
1. Retire do sistema o detector que vai limpar.
2. Cuidadosamente liberte cada uma das patilhas que seguram a tampa em posição
e retire a tampa.
3. Aspire ou utilize ar comprimido para remover o pó e a sujidade da área em redor
do termístor exposto.
4. Voltar a instalar a tampa do detector. Alinhe o LED com a tampa e encaixe-a em
posição certificando-se de que todas as patilhas de fixação da tampa estão
engatadas correctamente.
5. Quando tiver limpo todos os detectores, ligue de novo a alimentação para o
circuito e ensaie o detector conforme descrito na secção
ENSAIO
acima
.
AVISO – LIMITAÇÕES DOS DETECTORES DE CALOR
Os detectores de calor só funcionam quando estiverem ligados a um painel de
controlo compatível e operacional.
Os detectores de calor têm limitações de detecção. Não detectam fogos cujo
calor não chegue até aos detectores e tipos diferentes de detectores responderão
de forma diferente às várias condições de calor.
Os detectores de calor não duram indefinidamente e recomendamos a sua
substituição ao fim de 10 anos.
INSTALLATION AND MAINTENANCE INSTRUCTIONS FOR
THE THERMAL DETECTOR
SPECIFICATIONS
Supply Voltage:
8 - 30VDC
Quiescent current:(1005 and 1005T)
55µA
Typical at 24VDC, 25°C
Quiescent current:(1004T)
60µA
Typical at 24VDC, 25°C
Maximum alarm current: 80mA (Limited by panel or base resistance)
Latching Alarm:
Reset by momentary power interruption.
WARNING - Detector characteristics may vary from other manufacturer products.
Check compatibility with panel supplier for any limitations. eg: maximum quantity
of devices per circuit.
BASE MOUNTING AND WIRING INSTRUCTIONS
See figure 1 for terminal connections. Detector LED position marked by diode symbol
and arrow on base wall (See fig 1 *)
Notes: Do not loop wire under terminals: Break the wire run to ensure supervision of
connections.
All wiring must conform to applicable local and national codes and regulations.
Each ECO1000 base is fitted with a shorting spring to connect across terminals 1 and
2 to permit loop wiring to be checked before installation of detector heads. This spring
automatically disengages when the detector is fitted into the base.
I
MPORTANT - This detector is not compatible with the ECO1000BREL24L relay
base.
WARNING - Remove power from detector monitoring circuits before installing
detectors.
DETECTOR INSTALLATION
1. Place the detector into the detector base and rotate clockwise until the detector
drops into place. Continue rotating clockwise until the slot in the detector cover lines
up with the lines moulded in the base (See fig 2 **)
3. After all detectors have been installed, apply power to the detector monitoring
circuits.
4. Test the detector as described under
TESTING
.
Tamper-Resistance
The removal of the small plastic tab on the base indicated in figure 2 prevents the
removal of the detector head without a tool.
TESTING
Heat Method
1. Using a heat tool from an approved manufacturer such as No Climb Products Ltd,
apply in accordance with the suppliers instructions
2. The red LED on the detector should latch into alarm within 40 seconds, and the
control panel should activate into alarm.
Laser Test Tool Method (Model No. ECO1000RTU)
Note: This method does not carry out a complete functional test of the detector.
1. Align the flashing red spot produced by the laser beam with the LED on the detector.
2. The detector should latch into alarm within a few seconds, and the control panel
should activate into alarm.
MAINTENANCE
1. Remove the detector to be cleaned from the system.
2. Gently release each of the cover removal tabs that secure the cover in place and
remove the detector cover.
3. Vacuum or use compressed air to remove dust and debris from the area around the
exposed thermistor.
4. Reinstall the detector cover. Align the LED with the cover assembly and snap the
cover into place, ensuring that all the cover removal tabs are correctly engaged.
5. When all the detectors have been cleaned, restore power to the circuit and test the
detector as described in
TESTING
above.
WARNING - LIMITATIONS OF HEAT DETECTORS
Heat detectors will only work when connected to a functioning, compatible control panel.
Heat detectors have sensing limitations. They will not sense fires where heat does
not reach the detector, and different types of detector will respond differently to
various heat conditions.
Heat detectors cannot last forever, and we recommended replacement after 10 years.
EN
EN54-5: 2000 + A1: 2002
0832-CPD-1551 10 ECO1004TABLINK (Class BS)
0832-CPD-1552 10 ECO1005ABLINK (Class A1R)
0832-CPD-1553 10 ECO1005TABLINK (Class A2S)
Pittway Tecnologica Srl, Via Caboto
19/3, 34147 Trieste, Italy
