Symmetry 10001 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 53

background image

© 2014

42

Poor Linearity

Usually a
mechanical
problem

Electronic
Problems

Re-check repeatability
*Inspection of the flexures for damage or
loose hardware may be required
*Use the Linearity Function in the service
menu to reset linearity
*A problem in the analogue circuit board or
power supplies can cause poor linearity.
Make sure all mechanical problems have
been eliminated first

OTHER PROBLEMS:

Cannot calibrate

Zero shifted more
than allowed

Calibration
timeout

*Check all flexures for damage
*Reset dealer calibration
*Verify linearity and repeatability
*The balance may be unstable.  Verify
stability as above.

Calibration weight motor
does not stop

*Check the cables to the motor, try
plugging the balance into the power again
*Look for friction in the calibration weight
movement
*Check the opto-coupler that controls the
motor position.

RS-232 not working

Doesn’t print

Check parameters match the device
connected
Verify cable is correct
*RS-232 circuits damaged

Display dark, keys beep Display contrast

poor
Cable unplugged
or damaged

*Check the cables to the display
*Replace the display which could be
damaged

*To be carried out by authorised technicians only.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

«
...
42
43
44
45
46
...
»

Содержание 10001






















































Отзывы:

Нет отзывов

Похожие инструкции для 10001

Бренд: A&D Страницы: 104

Бренд: parktool Страницы: 2

Бренд: Sencor Страницы: 7

Бренд: Velleman Страницы: 34

Бренд: HiWeigh Страницы: 26

Бренд: Orbegozo Страницы: 18

Бренд: AEG Страницы: 58

Бренд: AEG Страницы: 62

Бренд: AEG Страницы: 92

Бренд: AEG Страницы: 108

Бренд: AEG Страницы: 96

Бренд: Dalman Страницы: 5

Бренд: INNOLIVING Страницы: 8

Бренд: Duronic Страницы: 32

Бренд: Atlanta Страницы: 18

Бренд: Cardinal Страницы: 12

Бренд: camry Страницы: 4

Бренд: UFESA Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды