Symmetricom ND-SERIES Скачать руководство пользователя страница 42

Страница: 42 / 47

ND Clocks User Manual- Rev 2.2.1 - Sep-08

Symmetricom

, Inc.

Compliance

Models:

ND-2-and ND-4, AC and POE versions

This equipment has been tested and found to comply with the radiated and line conducted limits for a

Class B digital device. These limits are designed to provide reasonable protection against harmful

interference in a commercial/residential installation.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation

Models:

ND-2-and ND-4, AC and POE versions

Electromagnetic Compatibility 89/336/EEC ; 92/31/EC ; 93/68/EEC ; 2004/108/EC

Tested and Conforms to the following EMC standards :

EN61000-3-2:2000 (Harmonic Current Emission)

EN61000-3-3:1995 + A1:2001 (Voltage Fluctuations & Flicker)

EN61000-4-2:2000, ,3,4,5,6,8,11

(ElectroStatic Discharge, RF Immunity, Fast Transient CM, Surge, RF Injection CM, Power Frequency

Magnetic Field, Voltage Dips)

EN61000-6-3:2001 (EMC Emissions –Generic Commercial)

EN55022:1998+A1:2000 +A2:2003

CISPR22

Low voltage directive 2006/95/EC

Tested and Conforms to the following Safety standards:

EN60950-1:2001 (Safety of Information Technology Equipment)

Waste Electrical and Electronic Equipment Directive (WEEE) 2002/95/EC

The ND models are considered WEEE Category 9 (Monitoring and Control Instruments)

Equipment as defined by the WEEE Directive and therefore fall within the scope of the

WEEE Directive.

For more information about Symmetricom’s WEEE compliance and recycle program, please

visit the Symmetricom WEEE/RoHS website at http:// www.Symmetricom.com/rohs.htm

Restriction of the Use of Certain Hazardous Substances Directive 2002/95/EC

The RoHS directive covers the same scope of electrical and electronic equipment that are

under the WEEE directive, except that Category 8, Medical Devices, and Category 9,

Monitoring and Control Instruments, which are under WEEE, are excluded from the RoHS

directive.

The time display products, Models: ND-2 and ND-4 , AC and POE versions

fall under the category of Monitoring and Control Instruments Equipment (Category 9 as

defined in Annex 1A of WEEE 2002/96/EC Directive) which is excluded from the RoHS

directive 2002/95/EC (reference Article 2, paragraph 1) requirements.

These products are manufactured using lead in the soldering process as allowed for

items excluded from the RoHS directive. These units are RoHS Compliant only in that

they are excluded from the RoHS directive under Category 9, Monitoring and Control

Instruments.

Содержание ND-SERIES
















































Результаты поиска

Содержание ND-SERIES

Отзывы:

Бренды по названию

Популярные бренды

Symmetricom ND-SERIES, Руководство пользователя

Результаты поиска

Содержание ND-SERIES

Отзывы:

Бренды по названию

Популярные бренды