Symbol Series 3300 Скачать руководство пользователя страница 68

Страница: 68 / 99

Error Recovery and Troubleshooting

4 - 11

The range is specified in page numbers (16KB per page). Use the right and left
arrow keys to move between the Start and End values. Use the up and down
arrow keys to change the page number value.

When you have set the range, press

Enter

10. The terminal displays the selected ranges for verification, for example:

RAM 0000 3FFF

NVM C839 DFFF

EMS None

Correct?

If the values are correct, press

Enter

. If the values are not correct, press

Clear

to clear the fields, and then select new values.

11. Specify the baud rate. Use the up and down arrows scroll through the list of

baud rates until the correct rate is displayed, and press

Enter

. (Flow control

may be necessary at 38400 bps and higher.)

12. Specify the data bits. Press

, or use the up and down arrows to display

7 or 8, and press

Enter

If you select 8 data bits, the program selects No parity and skips the next
screen.

13. Specify parity type. If you selected 7 data bits, the 3300 prompts for the parity.

Use the up and down arrows to display a parity option, or press the first letter
of a parity option (

ven,

dd,

one,

pace, or

ark), and press

Enter

14. Set flow control. Use the up and down arrows to display the flow control op-

tions, or you may press the first letter of an option (

one,

on/Xoff, or

TS/

CTS). Then press

Enter

Содержание Series 3300




































































































Результаты поиска

Содержание Series 3300

Отзывы:

Похожие инструкции для Series 3300

Бренды по названию

Популярные бренды

Symbol Series 3300, Руководство системного администратора

Результаты поиска

Содержание Series 3300

Отзывы:

Похожие инструкции для Series 3300

Бренды по названию

Популярные бренды