Symbol SE 923 Скачать руководство пользователя страница 181 | Manualshive

Страница: 181 / 238

background image

6-25

Simple Serial Interface

Parameter numbers 0xF0 (+256), 0xF1 (+512), 0xF2 (+768) are used to access parameters
whose numbers are 256 and higher. For example, to access the first parameter in the 256-511
range, use 0xF0 and 0x00.

Host Requirements

Note:

Due to the processing time of interpreting and storing parameters
contained in the message, it may not be possible for the decoder to
send an ACK within the programmable Serial Response time-out. It
should not be considered an error if the time-out is exceeded. To
compensate, increase the time-out.

The host transmits this message to change the decoder’s parameters. Be sure the Change Type
bit in the Status byte is set as desired. If no beep is required, the beep code must be set to 0xFF,
or the decoder beeps as defined in Table 6-4.

Decoder Requirements

When the decoder receives a PARAM_SEND, it interprets and stores the parameters, then
ACKs the command (if ACK/NAK handshaking is enabled). These parameters are stored
permanently only if the Change Type (bit 3 of the Status byte) is set to 1. If bit 3 is set to 0
the changes are temporary, and are lost when the decoder is powered down.

If the PARAM_SEND sent by the host contains a valid beep code, the decoder issues the
requested beep sequence, and changes the requested parameter values.

The decoder issues a PARAM_SEND in response to a PARAM_REQUEST from the host. It
sends the values for all the supported parameter values requested in the PARAM_REQUEST
message. No value is sent for any unsupported param_num. If none of the requested values
is supported, the PARAM_SEND message is transmitted with no parameters. When sending
this command, the Change Type bit (bit 3 of Status byte) can be ignored.

Table 6-9. Param Data Format

Parameter Number

Data Format

0 through 0xEF

<param_num> <value>

0xF0, 0xF1, 0xF2

<extended parameter code> <param_num offset>
<value>

«
...
179
180
181
182
183
...
»

Содержание SE 923















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SE 923

Бренд: Datalogic Страницы: 5

Бренд: SafeCom Страницы: 30

Бренд: Lazerlogic Страницы: 55

Бренд: Vantech Страницы: 2

ePort G9 Card Reader

Бренд: USA Technologies Страницы: 9

Бренд: Argox Страницы: 34

FZ-VSC552 Series

Бренд: Panasonic Страницы: 6

FZ-VSC551 Series

Бренд: Panasonic Страницы: 8

Бренд: Datalogic Страницы: 2

Бренд: Nordic ID Страницы: 12

Бренд: Nordic ID Страницы: 19

Бренд: Nordic ID Страницы: 19

Бренд: Datalogic Страницы: 14

Бренд: Datalogic Страницы: 20

Бренд: Datalogic Страницы: 88

Бренд: RIOTEC Страницы: 2

Бренд: RIOTEC Страницы: 2

Бренд: SmarTerminal Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды