Symbol LS 400Xi Скачать руководство пользователя страница 14

Страница: 14 / 136

2-4

LS 400Xi Product Reference Guide

Battery Box Operation

When using the LS 400Xi with a battery box, you can use either an alkaline battery
(recommended), or a nickel-cadmium rechargeable battery.

Changing the Battery

1. To open the battery box, push up on the flanges at one end of the pack.
2. Remove the old battery.
3. Insert the new or recharged 9-volt battery into the battery box. Match the

positive (+) and negative (-) terminals on the battery with the corresponding
terminals in the battery box.

Recharging a Nickel-Cadmium Battery

Remove the battery from the battery box and place it in the recharging unit (not supplied by
Symbol).

To recharge the battery, follow the instructions supplied with the recharging unit.

Содержание LS 400Xi









































































































































Результаты поиска

Содержание LS 400Xi

Отзывы:

Похожие инструкции для LS 400Xi

Бренды по названию

Популярные бренды

Symbol LS 400Xi, Руководство по продукции

Результаты поиска

Содержание LS 400Xi

Отзывы:

Похожие инструкции для LS 400Xi

Бренды по названию

Популярные бренды