Swiss Rotors FanSet SR190 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 21

Swiss Rotors FanSet SR190 Скачать руководство пользователя страница 10

10

Revision A.00

4

INSTALLATION – MOTOR CONNECTION

4.1 General safety

The following section contains valuable notes and list of mandatory procedures which are

responsibility of the user. Neglecting advices collected in this chapter may result in product

damage or void of warranty. Take time to study carefully whole chapter and make sure everything is

understandable. If you have any questions, please contact support.

FanSet needs to be installed in a way enabling seamless execution of future maintenance

tasks.

CAUTION!

Electric Voltage: All motors described in the following manual can be operated,

connected, installed, repaired and modified by qualified personnel only. Failure in performing

in any of this operations may result in risk of fatal injury, electric shock, incorrect mounting or product

damage. Installation should be carried out with usage of power lines, without short circuits and with

proper grounding. Follow the connection diagrams dedicated to given motors.

WARNING

: Do not open or disassemble the motor while power supply is connected to the device. It

may result in fatal injury caused by electric shock. If it is necessary to open the motor, wait at least

5 minutes after disconnecting from the power supply.

NOTE:

It is the user and the installer responsibility to provide the system with the proper grounding

and protection in accordance with national and local standards. Swiss Rotors is not responsible for

any damages or injuries caused by incorrect installation, bad circuits or other failures.

Before installation and operating the motor please read entire instruction carefully! Follow the

connection diagrams to perform successful installation.

4.2 Product description

Swiss Rotors Fans are equipped with various motor configurations tailored to the needs and

electrical requirements of our customers. To get the right parameters and to ensure proper operation

characteristics of the fans, range of motors includes a few basic configurations available. Table 2.1

shows the motors used in the fans and operating parameters – mechanical and electrical.

Note:

Given setups are explanatory. Swiss Rotors reserves the right to change those configurations

without informing. Any modification or configuration changes other than proposed should be

reported and consulted in details with Swiss Rotors technical department first.

«
...
8
9
10
11
12
...
»

Содержание FanSet SR190






















Отзывы:

Нет отзывов