background image

ǧ

LIMITED WARRANTY

The manufacturer’s warranty to the original consumer purchaser is:  This product is free from 
defects in materials and workmanship for a period of one (1) year from the date of purchase 
by the original consumer purchaser.

We will repair or replace, at our discretion, parts found to be defective due to materials or 
workmanship.  This warranty is subject to the following limitations and exclusions:

1) Engine Warranty

All engines utilized on our products has a separate warranty 
extended to them by the individual engine manufacturer.  Any 
engine service difficulty is the responsibility of the engine 
manufacturer and in no way is Swisher or its agents responsible 
for the engine warranty.  The Briggs & Stratton Engine Service 
Hot Line is 1-800-233-3723.

2) Commercial Use

This product is not intended for commercial use and carries no 
commercial warranty.

3) Limitations

This warranty applies only to products, which have been 
properly assembled, adjusted, and operated in accordance with 
the instructions contained within this manual.  This warranty 
does not apply to any product of Swisher that has been subject 
to alteration, misuse, abuse, improper assembly or installation, 
shipping damage, or to normal wear of the product.

4) Exclusions

Excluded from this warranty are normal wear, normal 
adjustments, and normal maintenance.

In the event you have a claim under this warranty, you must return the product to an
authorized service dealer.

All transportation charges, damage, or loss incurred during

transportation of parts submitted for replacement or repair under this warranty shall be borne
by the purchaser. Should you have any questions concerning this warranty, please contact us
toll-free at 1-800-222-8183. The model number, serial number, date of purchase, and the
name of the authorized Swisher dealer from whom you purchased the mower will be needed
before any warranty claim can be processed.

THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL 
DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME 
PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES.  Some states do not 
allow the limitation of consequential damages or limitations on how long an implied warranty 
may last, so the above limitations or exclusions may not apply to you.  This warranty gives 
you specific legal rights and you may have other rights, which vary from state-to-state. This is 
a limited warranty as defined by the Magnuson-Moss Act of 1975.

2

Содержание RC11544CL





















Отзывы: