54
If a water supply is fed by gravity then the
supply pressure should be verified to ensure
the conditions of use are appropriate for the valve.
i
Note:
In order to ensure the maximum
efficiency of the mixer, the operating
pressures (on hot and cold line) should be
kept as balanced as possible and the inlet
hot water must be at least 10°C above the
required blend temperature.
When pressure is higher than 5 bar a pressure
reducer is required to be fitted before the
mixer.
Drain down procedure
1. Close hot and cold mains feed taps.
2. Remove the shower hose from the mixer or
lay the showerhead and hose in the shower
tray to drain off any trapped water.
3. Turn bottom tap valve fully open
4. Turn the top thermostat valve fully clockwise
to drain cold water, until water stops flowing.
5. Push in the red temperature set button
on the top thermostat valve and turn fully
anticlockwise to drain the hot water side
until the water stops flowing.
Protecting your Thermostatic Mixing Tap
In addition to draining down the Thermostatic
Mixer Tap in periods of cold and freezing
conditions, to offer maximum protection it is
highly recommended that the Thermostatic
Mixer Tap is further protected by following the
method outlined below:
First complete the drain down procedure
ensuring the hot and cold feeds are isolated and
fully drained.
Using an allen key, remove the mixer body from
the tails by releasing the grub screws taking
care not to misplace these.
The unit can then be completely drained, dried
and wrapped in a soft cloth for storage away
from frost until required.
The Thermostatic Mixer Tap can then be re-
attached as follows;
Re-fit body to the tails and tighten the grub
screws, take care not to over tighten.
Re-connect to the water supplies and check
seals.
i
Note:
If after the drain down procedure
the Thermostatic Mixer Tap is to be left for
long periods in cold or freezing conditions,
leave the tap open and line up the ridge on
the thermostat hand wheel with the letter “H”
etched on the tap body.
General Care
Содержание Biarritz Lodge 40x13-2 2020
