background image

T82

1

2

3

4

1

2

7

D

ok

: 101540-

GB  2051

Engine

    1; Recoil starter
    2; Engine oil/dipstick
    3; Oil drain screw
    4; Silencer

Air Filter Check

The air filter must be checked at least once every           

working week. When working in dusty conditions,            

check daily.

Cleaning

1. Remove the filter lock and the filter element and check                       

that the filter element is undamaged. Replace damaged           

filter element.

2.

 

Strike the paper element against a hard object a few           

times to loosen any dirt.

Starting the engine

Start by pulling the starting handle. Pull it first until the

mechanism engages. Then pull it hard and fast. Press 

the lever down and hold it down until the flywheel has 

reached its maximum RPM. Then let it go.

STOPPING

Switch the engine to the idle position  idle, let it run for 

a few minutes, then switch it to stop. 

 

    1; Filter element
    2; Filter lock

OPERATING INSTRUCTIONS

1. Move the throttle to the working mode and the tamper 

will begin to move.

Note! 

During operation, the engine must always work at 

full throttle (working mode).

2. Guide the tamper with guide handle.

3. Take care that the shoe hits parallel to the ground.

4. Do not fight or overpower the machine.

Note! Never work on hard surfaces (solid rock, 

hardened concrete or such). When working in 

trenches always make sure that they are wide 

enough. When working in a narrow trench, the 

ramming shoe should get caught between the walls 

of the trench, the rammer may mis-strike and can be 

severely damaged. The ramming shoe may especially 

be damaged severely. Make certain that the rammer 

is steared only by using the hand grip. It should only 

be pushed. The rammer must not be pressed into the 

materials being compacted. Excessive pressure to 

the operation handle will lead to the unsatis factory 

compaction due to the fact that the jumping action 

is hindered. If the machine falls over while working, 

switch off the engine before raising it.

5. Put the throttle in the stop mode. Fuel supply to the 

engine is cut off in this mode, tank ventilation is closed 

and the engine switch is Off.

START Honda engine

Содержание T82


















Отзывы: