GB.TBLZ75.150526
We reserve the right to alter specifications.
www.swegon.com 3
Table:
MAIN MENU SETTINGS
DESCRIPTION
VALUE
Status
Set Setpoint
With the Hand-held micro terminal set to the "HTERM" mode in the "Start/Stop"/"Control" menu, set the required
set point in the EC in %. With the Hand-held micro terminal in the "0-10VDC" mode in the "Start/Stop"/"Control"
menu, read the current set point in %.
0 – 100 %
% Out
Shows the current speed of rotation as a percentage of the range (See Section 11).
0 – 100 %
Rpm Out
Shows the current speed of rotation
0 - ?* min-1
Power
Shows current input power
0 - ?* kW
External Set
Shows the current voltage on the External setting input
0 - 10.0 V
External STOP
Shows the current status on the ON/OFF input, Terminals 7 and 8.
”1” = Stop /
”0” = Start
External FIREMODE
Shows the current status on the fire input, Terminals 9 and 10.
”1” = Normal /
”0” = Brand
Op. time
Shows the current operating time as number of days.
0 - ? days
Op. time
Shows the current operating time in minutes.
0 - ? minutes
I out
Shows present output current
0 -?* A
V in RMS
Shows current input voltage
0 - ?* V
Temp.
Shows the current temperature inside the control system.
? - ? °C
Exit
Return to the Main menu.
Start/Stop
Operation
Start/Stop the motor
Stop/Start
Control
Selection of control signal
Control = HTERM
EC is controlled from the hand-held micro terminal.
External signals are ignored, including:
Start/Stop on Terminals 7 and 8 (ON/OFF).
The fire signal on Terminals 9 and 10 (Firemode) as well as the external control signal on Terminals 13 and 14 (0 – 10 V in).
Control = 0-10 V DC
EC is controlled from external control signals, including:
Start/Stop on Terminals 7 and 8 (ON/OFF).
The fire mode signal on Terminals 9 and 10 (Firemode) as well as the external control signal on Terminals 13 and 14 (0 –
10 V in).
External stop and stop from the hand-held micro terminal have higher priority than start from the hand-held micro
terminal.
HTERM / 0-10 V DC
FIRE
Activate the Fire mode. "Fire" from the hand-held micro terminal or external input have higher priority than "Nor-
mal". Important! For high internal temperature inside the EC control system, the display window backlight is turned
off when "Fire" is active.
”1” = Fire /
”0” = Normal
Exit
Return to the Main menu.
Alarms
Reset Alarm
Is activated in order to reset alarms when the maximum number of restarts has been exceeded.
Alarm stop
Shown when the motor has stopped due to an alarm.
Voltage low
Shown when an alarm has been initiated due to excessively low line voltage.
Voltage high
Shown when an alarm has been initiated due to excessively high line voltage.
Phase error
Shown when an alarm has been initiated because one line voltage supply phase is missing.
Current high
Shown when an alarm has been initiated due to excessively high output current.
Current limiting
Shown when an alarm has been initiated because the current limiting function is active (e.g. if the ramp time is
excessively short or if the motor is overloaded).
I ripple
Shown when an alarm has been initiated due to unstable line voltage.
Temperature high
Shown when an alarm has been initiated due to excessively high temperature in the frequency inverter.
Rotor Blocked
Shown when the rotor is blocked.
Internal error
Shown when an alarm has been initiated due to an internal fault inside the frequency inverter.
EC com. error
Internal communication error between the junction box and the EC- control system.
Exit
Return to the Main menu.
Edit setup
Min. rpm
Setting of the lowest speed of rotation (See also Section 11).
0 - ?* min-1
Max. rpm
Setting of the highest speed of rotation (See also Section 11).
0 - ?* min-1
Up Ramp
Setting of the ramp up time (See also Section 10).
0 - ?* s
Down Ramp
Setting of the ramp down time (See also Section 10).
0 - ?* s
Switch Hz
Setting of the switching frequency on the output.
Auto, Low, High
Exit
Return to the Main menu.
Modbus
Address
Setting of the Modbus address display.
Baudrate
Setting of the baudrate display.
4 800, 9 600,19 200,
38 400, 57 600,
115 200 Bps.
Parity
Setting of the parity display.
None/Odd/Even
Stop bits
Setting and display of stopbits.
None/1/2
Exit
Return to the Main menu.
About EC
SLAVE ADDRESS
Status of the EC control system's internal address.
EC type
Status of the type of EC control system.
1000- ?*
FC SW ver.
Status of the EC control system's program version.
I/O SW ver.
Status of the I/O module's program version.
Boot SW ver.
Status of the EC control system's boot program version.
Term SW ver.
Status of the hand-held micro terminal's program version.
Exit
Return to the Main menu.
*= Depends on size of the connected control system
