SwedeSolutions Litecam P2 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 28

SwedeSolutions Litecam P2 Скачать руководство пользователя страница 28

Installation manual

Litecam P2

QUICK REFERENCE/START GUIDE

CFE Plus (WiFi)

© 2020 SwedeSolutions the Netherlands - [email protected] - www.swedesolutions.com

Instruction# 1669

Version# 0.8

Part# -

EAN# SE-12

Author: KW

28/30

FAQ:

Questions:

Q: Can I wash my car in an automatic car cleaning box?

A: yes, of course. The camera is water resistant. Normal washing is no problem. Putting a high
pressure water jet on it might damage the camera though, so avoid that.

Q: Sometimes the image is a bit “vague”, not “clear”

A: Simply clean the camera lens with a soft tissue. Since the camera is mounted at the trunk,
it will get dirty..

Q: Sometimes a part of the image is dark or very light.

A: that has to do with the minimum and maximum amount of light the camera thinks is re-
quired to display the best image. If 60% of the image is very bright, the camera will close its
iris and darken the image. The darker parts will then get even darker. Same goes for the other
way around. This is how any camera works by the way.

Q: the Camera does not switch off immediately if I put my car in D or first gear after I finished
reverse parking.

A: this i

s as designed. To avoid very fast and rapid switching while you’re parking the car (re-

versing, back in 1

st

gear, reversing etc.) the camera will stay active for about 6-7 seconds after

the reverse gear is switched off.

«
...
26
27
28

Содержание Litecam P2





























Отзывы:

Нет отзывов