SwedeSolutions Litecam P2 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 28

SwedeSolutions Litecam P2 Скачать руководство пользователя страница 17

Installation manual

Litecam P2

QUICK REFERENCE/START GUIDE

CFE Plus (WiFi)

© 2020 SwedeSolutions the Netherlands - [email protected] - www.swedesolutions.com

Instruction# 1669

Version# 0.8

Part# -

EAN# SE-12

Author: KW

17/30

Next you connect the supplied extension cable to the camera harness. Then follow the red line
with the extension cable and make sure you tape the harness together with existing wires.

Guide the wire out now trough the rubber as shown below.
The best way is to guide the harness in parallel with the original wiring coming out.

If you can’t

get the mini connector trough, it is ok to make a small whole as shown in the right picture.

Remove the cable guidance (left arrow on left picture) and guide the camera harness next to
the original wiring there. Use some tape to tighten the camera harness to the original wiring.
Last point is to push the camera harness into the car again, trough the rubber as well at this
point.

«
...
15
16
17
18
19
...
»

Содержание Litecam P2





























Отзывы:

Нет отзывов