manualshive.com logo in svg

Swecoin TTP 2000, Руководство по обслуживанию

Поделиться
Скачать
Swecoin TTP 2000 Скачать руководство пользователя страница 11

  

Installation 

0701 

TTP 2000 Kiosk Printer–Service Manual 

11 

3.2  Making a test printout 

1. Load 

paper 

2.  Switch OFF the power. 

3.  Hold the feed-forward button depressed while powering ON 

the printer. Keep the button depressed until printing starts. 

This produces a printout showing the firmware program version 
and date, control board revision number and serial number, 
name of loaded fonts and logotypes, and the parameter 
settings. 

4.  Each successive press of the button will produce a test 

printout. 

Switch the printer OFF and ON again to exit self-test mode. 

 

If a power button is not available for the printer, follow the 
below procedure: 

1.  Lift the printhead 

2.  Hold the FF-button pressed while lowering the head 

and hold it pressed while an auto load of paper is done 

3.  Release the button and a self-test printout will be printed 

4.  The printer exits self-test mode and goes on-line 

1

0

Self-test

Содержание TTP 2000
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды